Km & Olivetti Error Codes

Transcript

    OLIVETTI ERROR CODES D16/200/250 MODELS AND KYOCERAKM1620/50 KM2020/50 KM2550 MODELS   CODE CONTENTS CAUSES C0030Fax control PCB*1 system problemã Processing with the fax software wasdisabled due to a hardware or softwareproblem.Fax control PCB*1Defective fax controlPCB. C0070Fax control PCB*1 incompatibilitydetection problemã Fax software is not compatible withMMI software.Fax software ormain software issomething of theother machine. C0100Backup memory read/write problem(main PCB flash)ã Read and write data does not match.DefectivemainPCB. C0110Backup memory data problem (mainPCB flash)ã Data in the specified area of thebackup memory does not match thespecified values.Problem with thebackup memorydata.Defective backupRAM. C0130Backup memory read/write problem(main PCB EEPROM)ã Read and write data does not match.DefectiveEEPROM or mainPCB. C0140Backup memory data problem (mainPCB EEPROM)ã Data in the specified area of thebackup memory does not match thespecified values.Problem with thebackup memorydata.DefectiveEEPROM. C0150Backup memory read/write problem(engine PCB)ã Read and write data does not match.Defective enginePCB.   C0160Backup memory data problem (enginePCB)ã Data in the specified area of thebackup memory does not match thespecified values.Problem with thebackup memorydata.Defective backupRAM. C0170Accounting count problemã When the power is turned on, the totalcount and the scan count are abnormalboth on the main PCB and theengine PCB.Defective mainPCB or enginePCB. C0180Machine number mismatchã When the power is turned on, the machinenumber does not match betweenthe main PCB and the enginePCB.Correct EEPROMis not installed.Data damage of EEPROM. C0210Communication problem betweenthe main PCB and engine PCBã When the power is turned on, the machinedoes not detect the low level of SBSY and the high level of SDIR for10 s.Poor contact inthe connector terminals.Defective mainPCB or enginePCB. C0240Printer board PCB communicationproblemã The printer board PCB does not respond120 s after the power is turnedon.Poor contact inthe connector terminals.Defective mainPCB or printerboard PCB. C0250Scanner network board*1 communicationproblemã The scanner network board does notrespond.Poor contact inthe connector terminals.Defective mainPCB or scannernetwork board. C0280Fax control PCB*1 communicationproblemã Communication between the fax controlPCB and the main PCB of themachine cannot be performed normally.Poor contact inthe connector terminals.Defective mainPCB or fax controlPCB. C0410DP*1 communication problemã Communication fails five timessuccessively.DP installed incorrectly.Defective enginePCB or DP driverPCB.   C0420First paper feeder*2 communicationproblemã Communication fails five timessuccessively.Paper feeder installedincorrectly.Defective enginePCB or drawermain PCB. C0440Finisher*1 communication problemã Communication fails five timessuccessively.Finisher installedincorrectly.Defective enginePCB or finishermain PCB. C0500Second paper feeder*1 communicationproblemã Communication fails five timessuccessively.Paper feeder installedincorrectly.Defective enginePCB or drawermain PCB. C0510Third paper feeder*1 communicationproblemã Communication fails five timessuccessively.Paper feeder installedincorrectly.Defective enginePCB or drawermain PCB. C0610Bitmap (DIMM) problemã There is a problem with the data oraddress bus of the bitmap DRAM.Defective mainPCB.DIMM installedincorrectly.Defective DIMM. C0630DMA problemã DMA transmission of compressed,decompressed, rotated, relocated orblanked-out image data does notcomplete within the specified periodof time.Defective mainPCB. C0800Image processing problemã JAM05 is detected twice.Defective mainPCB. C0820Fax control PCB*1 CG ROMchecksum errorã A checksum error occurred with theCG ROM data of the fax control PCB.Defective fax controlPCB. C0830Flash ROM program area checksumDefective fax control  errorã A checksum error occurred with theprogram of the fax control PCB.PCB. C0860Fax control PCB*1 software switchchecksum errorã A checksum error occurred with thesoftware switch value of the fax controlPCB.Defective fax software.Defective fax controlPCB. C0870Fax control PCB*1 to main PCB highcapacitydata transfer problemã High-capacity data transfer betweenthe fax control PCB and the mainPCB of the machine was not normallyperformed even if the data transferwas retried the specified times.Poor contact inthe connector terminals.Defective mainPCB or fax controlPCB. C0880Fax control PCB*1 program archiveproblemã When power is turned on, the compressedprogram in the Flash ROMon the fax control PCB was not successfullydecompressed.Defective fax controlPCB. C0890Fax control PCB*1 CG font archiveproblemã When power is turned on, the compressedCG font in the Flash ROM onthe fax control PCB was not successfullydecompressed.Defective fax controlPCB. C0900Fax software incompatibility detectionproblemã Version of fax software is not compatiblewith that of main software.Fax software versionor main softwareis earlier. C0920Fax file system errorã The backup data is not retained forfile system abnormality of flashmemory of the fax control PCB.Defective fax controlPCB. C2000Drive motor problemã LOCK ALM signal remains high for 1s, 1 s after the drive motor has turnedon.Poor contact inthe drive motorconnector terminals.Defective drivemotor rotation