Packaging

Transcript

Packaging Presented By Siddhartha Sen, IIT Kharagpur  Under the Guidance of : Prof. A. Dasgupta Topics  Functions of the Package  Different Kinds of Packages  Rent’s Rule  VLSI Assembly Technology  System on Chip versus System in Package  3 – D Pa Pack ckag agiing  Chip on Chip (CoC)  Electrical Performance  Thermal Management  Common Failure Mechanisms and Reliability  Future Trends Packaging Topics  Functions of the Package  Different Kinds of Packages  Rent’s Rule  VLSI Assembly Technology  System on Chip versus System in Package  3 – D Pa Pack ckag agiing  Chip on Chip (CoC)  Electrical Performance  Thermal Management  Common Failure Mechanisms and Reliability  Future Trends Packaging Func Functi tion ons s of of the the Pack Packag age e-I  Packages shut out damaging external influences like Moisture, Dust, Vibration, Shock, Lightning, Magnets, etc and serve to protect silicon chips.  Lead frame allows electrical signals to be sent and received to and from semiconductor devices. Pack Packag agin ing g-1 Functions of the Package -II  Packages effectively release the heat generated by the chip during its operation.  Packages allow for enlargement of terminals size that makes the chips much easier to handle. Pack Packag agin ing g-2 Types of Packages  Though a wide variety of packages can be used for VLSI devices, they can be broadly divided into two basic types:  Hermetic Ceramic Packages: The chip resides in an environment decoupled from the external environment by a vacuum tight enclosure. The packages are usually designed for high performance applications that allow some cost penalties  Plastic Packages: The chip is not completely decoupled from the external environment because it is encapsulated with resin materials, typically epoxy based resins. They are extremely cost competitive and their popularity persists because of rapid advances in plastic technology Pack Packag agin ing g-3 Types of Packages (Hermetic Packages)  The chip resides in a cavity of the package. Chip  Package base material is ceramic usually Al203 or AlN.  The chip and the package are connected by fine Al wire.  Hermetic sealing is completed by a cap, usually ceramic or metal, lidded to the package. Seal Ring Leads Traces  A Typical Hermetic Package Packaging - 4 Types of Packages (Plastic Packages)  The chip is attached to the package of the lead frame.  The frame is made of etched or stamped thin metal( usually Fe-Ni or Cu alloys).  Interconnections are made by fine gold wire.  Encapsulation is carried out by Transfer-molding using epoxy resin. Packaging - 5 Molding Material Chip Support Paddle Spot Plate Bond Wires Types of Packages (PWB level) Packaging - 6 Rent’s Rule Prediction  Rent’s Rule is an empirical relationship between the gate count and the I/O (Terminal) Count in a Chip. Microprocessors Logic Array Number (I/O Count ) = α (Number of gates) Typically: α = 4.5 β = 0.5 β DRAM Memory : 1 Kbits – 1024 Kbits Microprocessors : 4 – 32 bits Gate Arrays : 50 – 16K gates Packaging - 7 VLSI Assembly Technologies Wafer Solder Preform Polymer Adhesive Al wire / Au wire Conformal Coating Metal Preform Polymer Seal Molding Compound Wafer Preparation Wafer Backgrinding Die Preparation Die Bonding Adhesive Die Bonding Die Interconnection Wire Bonding, TAB, Molding Transfer molding Eutectic Die Bonding Flip Chip Package Seal Marking DTFS Ink Marking Laser Marking Deflash-Trim-FormSingulate Wafer Backgrinding  Wafer Backgrind is the process of grinding the backside of the wafer to the correct wafer thickness prior to assembly.  Wafers normally undergo a cleaning and surface lamination process prior to the actual backgrinding process.  The grinding wheel parameters are: speed, spindle coolant water temperature and flow rate, initial and final wafer thickness, and feed speeds.  Continuous washing of the wafer is also done during the backgrinding process to remove debris. Packaging - 9 Die Preparation   Wafer Mounting: frame loading, wafer loading, application of tape to the wafer and wafer frame, cutting of the excess tape and unloading of the mounted wafer  Wafer mounted on wafer frames Wafer Films Wafer Saw: alignment, cutting by resin-bonded diamond wheel, cleaning Packaging - 10 Wafer Saw Blades Die Bonding  Die Bonding is the process of attaching the silicon chip to the die pad or die cavity of the support structure.   Adhesive Die Attach: Uses adhesives such as polyimide, epoxy and silver-filled glass as die attach material  Eutectic Die Attach: Uses a eutectic alloy to attach the die to the cavity. The Au-Si eutectic alloy is the most commonly used Packaging - 11 D/A adhesive as the grainy material between the die and die pad Normal Eutectic Die Attach and with Balling Die Interconnection: Wire Bonding  The wire is generally made up of one of the following:  Gold  Aluminum   Copper  There are two main classes of wire bonding:  Ball bonding  Wedge bonding Wire Bonds Packaging - 12 Wire Bonding (Ball-Bonding)   A gold ball is first formed by melting the end of the wire.   The free-air ball brought into contact with the bond pad, adequate amounts of pressure, heat, and ultrasonic forces are then applied. The wire is then run to the corresponding finger of the leadframe, forming a gradual arc or "loop" between the bond pad and the leadfinger. Packaging - 13 The 1st Bond The 2nd Bond Gold wire ball-bonded to a gold contact pad Wire Bonding (Wedge Bonding)   A clamped wire is brought in contact with the bond pad. Ultrasonic energy and pressure are applied.  The wire is then run to the corresponding lead finger, and again pressed. The second bond is again formed by applying ultrasonic energy to the wire. Packaging - 14 1st Wedge Bond Aluminum wires wedge-bonded Die Interconnection: Flip Chip  The term “Flip-chip” refers to an electronic component or semiconductor device that can be mounted directly onto a substrate, board, or carrier in a ‘face-down’ manner.  Electrical connection is achieved through conductive bumps built on the surface of the chips, which is why the mounting process is ‘facedown’ in nature. Packaging - 15 Flip Chip Bumps Flip Chip - Advantages   Smallest Size  reduces the required board area by up to 95%  requires far less height Highest Performance  reduces the delaying inductance and capacitance of the connection by a factor of 10  highest speed electrical performance of any assembly method  Most Rugged  Lowest Cost Packaging - 16 Tape Automated Bonding (TAB)   A  process that places bare chips onto a printed circuit board (PCB) by attaching them to a polyimide film. The film is moved to the target location, and the leads are cut and soldered to the board. The bare chip is then encapsulated ("glob topped") with epoxy or plastic. Packaging - 17 Molding  Molding is the process of encapsulating the device in plastic material.  Transfer molding is one of the most widely used molding processes in the semiconductor industry.  The cavities are filled up in a 'Christmas tree' fashion - The highest filling velocity is experienced by the first cavity.  Subsequent cavities are filled with increasing velocities until the last cavity, which ends up with the second highest filling velocity.  Wiresweeping and die paddle Packaging - 18 Mold Chases Examples of Molds Package Sealing  Sealing is the process of encapsulating a hermetic package, usually by capping or putting a lid over the base or body of the package. The method of sealing is generally dependent on the type of package.  Ceramic DIPs, or cerdips, are sealed by topping the base of the package with a cap using seal glass.  Seal glass, like any glass, is a supercooled liquid which exhibits tremendous viscosity when cooled below its glass transition temperature. A seal glass may be classified as vitreous or Devitrifying. Packaging - 19 Marking  Marking is the process of putting identification, traceability, and distinguishing marks on the package of an IC.  The most common Ink marking process for semiconductor products is Pad printing. Pad printing consists of transferring an ink pattern from the plate, which is a flat block with pattern depressions that are filled with ink, to the package, using a silicone rubber stamp pad.  Laser marking refers to the process of engraving marks on the marking surface using a laser beam. There are many types of lasers, but the ones used or in use in the semiconductor industry include the CO2 laser, the YAG laser, and diode lasers. Packaging - 20 Deflash/Trim/Form/Singulation (DTFS) 1. Deflash - removal of flashes from the package of the newly molded parts. Flashes are the excess plastic material sticking out of the package edges right after molding. 2. Trim - cutting of the dambars that short the leads together. 3. Form - forming of the leads into the correct shape and position. 4. Singulation - cutting of the tie bars that attach the individual units to the leadframe, resulting in the individual separation of each unit from the leadframe. Packaging - 21 System on Chip ( SoC ) versus System in Package (SiP)  SoC is a technology that allows a system to be built on one silicon chip (bare chip).  SiP is a package technology that combines a multiple number of readymade chips (such as logic and memory) and encases them in one package as one system. Packaging - 22 SiP Categories Packaging - 23 3D Packaging: Introduction  The driving forces are the significant size and weight reductions, higher performance, small delay, higher reliability and reduced power.  3 D Packages score over conventional packages in:  Size and Weight  Silicon Efficiency  Interconnect Usability and  Accessibility  Delay  Noise  Power Consumption  Speed Packaging - 24 Four-die stack including two spacers 3D Packaging Types of 3D Packages  Stacked Die Packages: Consists of bare die stacked and interconnected using wire bond and flip-chip connections in one standard CSP  Stacked-Packages: consist of stacked, pre-tested packages or a mix of KGD and packages. These are interconnected using wire bond, flip chip or solder balls on one CSP  They can be:  Package-in-Package (PiP)  Package-on-Package (PoP) Packaging - 25 PiP structure with 4 stacks PoP structure with 4 stacks 3 D Packaging: Advantages - I  The shift from conventional single chip packages to 3D technology, leads to substantial size and weight reductions: Volume ( in cm3 / Gbit ) Type Capacity Discrete Planar 3D Discrete/3D Planar/3D SRAM 1 Mbit 1678 783 133 12.6 5.9 DRAM 1 Mbit 1357 441 88 15.4 5.0 Mass ( in grams / Gbit ) Type Capacity Discrete Planar 3D Discrete/3D Planar/3D SRAM 1 Mbit 3538 2540 195 18.1 13.0 DRAM 1 Mbit 2313 1542 132 17.5 11.6 Packaging - 26 3 D Packaging: Advantages - II   Increase in Silicon Efficiency. Interconnect Usability and  Accessibility. Packaging - 27 3 D Packaging: Advantages - III  Delay Reduction  Noise Reduction  Power Reduction  Speed Increase Packaging - 28 3 D Packaging: Limitations  There are trade-offs which need to be taken into account when using 3D technology in system design:  Thermal Management  Design complexity  Cost  Time to Delivery  Design Software Packaging - 29 Electrical Considerations: Introduction  The choice of a package for an integrated circuit depends on the electrical and thermal conditions under which the chip is expected to operate. In other words, the package must satisfy a set of electrical and thermal requirements formulated for the application at hand.  The electrical operating conditions of an integrated circuit can be viewed as consisting of two distinct environments: one for Signals and another for Power . The requirements for these environments are substantially different. Packaging - 30 Electrical Considerations: The Signal Environment  The signal's electrical environment is the arrangement of conductors and dielectrics. Electrically, each segment of this path represents a transmission line with certain characteristic impedance and time delay. Also involved are the inductances of the bond wires and package pins.  Usually, the leads are not of controlled impedance and each possesses substantial inductance and capacitance. Relatively strong inductive and capacitive coupling (M and C) exist between the leads.  The major issues in the signal environment are Signal Delay, Signal Reflection and Noise Reduction. Packaging - 31 Electrical Considerations: The Signal Environment  Signal Delay  High speed operation requires lower interconnect delays. The maximum achievable operating frequency is obviously the inverse of the critical delay path.  In package construction, a short signal line (bonding wire length plus lead length) in small dielectric material, typically polyimide resin, is preferable.  An excessively small dielectric constant of the surrounding material, however induces signal reflections that degrade operating speed. Packaging - 32 Electrical Considerations: The Signal Environment  Signal Reflection:   Mismatched impedances cause signal reflections when a signal is l transmitted via a transmission line. The transmission line character cannot be ignored when the signal lines are long c < v0 ε  Multilayered packages like stripline structures and microstrip structures provide better impedance matching Packaging - 33 r  Stripline conductor Microstrip conductor Electrical Considerations: The Signal Environment  Noise: The two kinds of noise of importance are Cross-Talk noise and Simultaneous switching noise:  Cross Talk Noise: Line is undesirably affected by another line due to electromagnetic coupling  Simultaneous Switching Noise: Occurs when many output buffers switch simultaneously Packaging - 34 Cross Talk on Adjacent Lines Tx Line Simultaneous Switching Noise Electrical Considerations: The Power Environment  Inductances in the power circuit cause instability of the potentials at the power and ground terminals of the chip:  Power Supply Droop  Ground Bounce Packaging - 35 Electrical Considerations  The Desirable Electrical Characteristics: Low ground resistance (minimum power supply voltage drop)  Minimum Self Inductance of signal leads (short signal leads)  Minimum power supply spiking due to simultaneous switching of signal lines.  Minimum Mutual Inductance and Cross Talk (short paralleled signal runs)  Minimum Capacitive loading (short signal runs near a ground plane)  Maximum use of Matched Impedances (avoid signal reflection)  Packaging - 36 Thermal Management  Efficient and cost-effective removal of dissipated thermal energy from the device to assure its reliable performance over the long term.  Effects of Increasing Temperatures:  Device physics is strongly influenced by the junction temperature  Corrosion and interfacial diffusion mechanisms  Approximately a 10°C increase in temperature reduces the mean time to failure by a factor of two Packaging - 37 Thermal Management (Thermal Resistance)  The internal temperature (called junction temperature) is equal to the ambient temperature plus an offset proportional to the internal power dissipation P. It is given by: T junction = Tambient + θJA.P  The constant of proportionality  Current Trends:  θJA is called the thermal resistance  The total power is going up due to improper scaling, higher packing density, and lower chip size  Maximum ambient being as high as 60 °C  Maximum junction temperatures from 105 °C to 65 °C The total thermal resistance of the package must decrease: θJA = θJC + θCA Packaging - 38 Thermal Management   A Simplified Heat transfer model: Heat is transferred from the chip to the surface of the package by conduction and from the package to the ambient by convection and radiation: Ta Thermal Convection & Radiation Tc Conduction T j θJA = θJC + θCA = ((T j-Tc) + (Tc-Ta))/P Chip θJC is mainly a function of package materials and geometry θCA depends PWB Simplified Heat Transfer Model of a packaged chip on package geometry, the package orientation and conditions of ambient. Packaging - 39 Thermal Considerations  Conduction dominates heat transfer from chip to package surface. One Dimensional Fourier’s equation gives: Q = (T1 – T2)*κ*(S/L) In the actual package: P = (T j – Tc)*κ*(S/L) Thus we have: θJC = (T j – Tc)/P = L/(κ*S)  VLSI packages have a high packing density (small S) so high thermal conductivity components such as Cu alloys lead frames, AlN substrates and thermo-conductive molding compounds are particularly important as they increase overall package κ value.  Thinner packages (low L) are also important. Packaging - 40 Thermal Considerations  Convection: Heat transfer from the package surface to the ambient results mostly from convection, given by Newton’s Cooling Law: Q = h*A*(Tc – Ta) Therefore: θCA = (Tc – Ta)/P = 1/(h*A) θCA is reduced through increased conduction and larger package surface area. The application system constructions are forced air convections, liquid coolants in place of air coolings and additional heat sinks attached to the package surface. Packaging - 41 Thermal Considerations  Radiation helps transfer some heat from the package surface to the ambient, but usually the contribution is small.  According to Stefan-Boltzmann Law: Eb = ε*σ*T4 The heat radiated is: Q = σ*f*A*(T14 – T24) Where f is given by: f = 1/((1/ε1)+(1/ε2)-1) When T1-T2<