Transcript

Preliminary Issue

DXX-2300-2690/3300-3800-90/75-16i/15.5i-M/M-R
Model: ATD4516R9

Antenna Specifications

General Electrical Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690 3300 - 3800

General Polarization +45° , -45°
parameters Electrical downtilt (°) 2 - 12 , continuously adjustable
Grounding DC Ground
Coupling factor between calibration port and each
-26
antenna port (dB)
Max. amplitude tolerance from calibration port to
0.9
input ports (dB)
Calibration and
electrical Max. phase tolerance from calibration port to input
7
parameters ports (°)
Ports VSWR 1.5
Co-polarization isolation between ports (dB) 20
Cross-polarization isolation between ports (dB) 25

Beamforming Electrical Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690 3300 - 3800
Horizontal 3dB beam width (°) 90 80 85
Gain (dBi) 15.2 16 14.5
Single
Cross polar ratio (0°) (dB) 18 18 18
column
beam Side lobe suppression for first side
15 15 15
lobe above main beam (dB)
Front to back ratio (dB) 23 23 23
Horizontal 3dB beam width (°) 65 65 65
Gain (dBi) 16.7 17 16

Radiation 65° Vertical 3dB beam width (°) 6 5.6 5.5
parameters Broadcast Cross polar ratio (0°) (dB) 18 18 18
beam
Front to back ratio (dB) 25 25 25
Side lobe suppression for first side
15 15 15
lobe above main beam (dB)
0° direct beam gain (dBi) 20.2 21 20
0° direction beam horizontal 3dB
26 25 26
beam width (°)
Service
beam 0° direction beam cross polar ratio
18 18 18
(0°) (dB)
0° direction beam front to back ratio
28 28 28
(dB)

Soft Split Electrical Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690 3300 - 3800
Horizontal 3dB beam width (°) 30 27 30
Gain (dBi) 19.7 20.5 19
Radiation
parameters Vertical 3dB beam width (°) 6 5.6 5.5
Multi-beam
Front to back ratio (dB) 25 25 25
Side lobe suppression for first side
15 15 15
lobe above main beam (dB)
Notes：
65° broadcast beams and multi-beams are applicable in different scenarios. Select one of them for network coverage based on
site requirements and auxiliary equipment conditions.
1

EN/IEC 60950-22(Safety – Equipment installed outdoor). operational wind speed (km/h) 200 Survival wind speed (km/h) 250 Connector 18 x N Female Connector position Bottom Antenna Information Management Module (AIMM) Specifications RET Properties RET type Integrated RET(SingleRET) RET protocols AISG 2. +65 Frontal: 675 (at 150 km/h) Wind load (N) Lateral: 185 (at 150 km/h) Rear side: 645 (at 150 km/h) Max. 3. P. 4. HUAWEI ‘s standard brackets and accessories must be used for any installation. 12 V) Adjustment time (full range) (s) Typ. Ltd.5i-M/M-R Model: ATD4516R9 Mechanical Properties Antenna dimensions (H x W x D) (mm) 1445 x 469 x 206 Packing dimensions (H x W x D) (mm) 1600 x 530 x 270 Antenna net weight (kg) 32 Mast diameter supported (mm) 50 . FCC. 12 V) Power consumption (W) < 3 (when the motor is working.huawei. Bantian. IC. ETSI EN 301 489. depending on antenna type) One pair of 8-pin AISG connectors compliant with the IEC 60130-9 standard [DC (pin 6&pin 1). EN 55024(Immunity). Huawei Technologies Co. 2 Issue: 2017-04-12 .. REACH. ICES-003 Certification: CE. 2. The antenna working environment must meet the requirements specified in the datasheet. Longgang District. Preliminary Issue DXX-2300-2690/3300-3800-90/75-16i/15. 30 (typically.com/antenna Any previous datasheet issues become invalid. RS485 A/B (pin 5/pin 3)] Two AISG-OOK connectors inside the antenna Lightning protection (kA) 5 (8/20 μs) RAE Properties RAE type Integrated RAE RAE protocols AISG-ES-RAE V2.0 / 3GPP Input voltage range (V) 10 V DC to 30 V DC < 1 (when the motor does not work. such as towers and poles.1. must bear the weight and wind load of antennas. DC Connectors return (pin 7). EN 55032(Emission). Installation tools and procedures must conform to requirements described in the antenna installation guide. Facilities. RoHS. 12 V) < 10 (when the motor is starting up or shutting down.0 Standards: EN/IEC 60950-1(Safety). Shenzhen 518129. RCM..R. FCC part15.115 Radome material Fiberglass Radome colour Light grey Operational temperature (℃) -40 . WEEE NOTE 1.China www. Only qualified personnel are allowed to perform installation.