Transcript
AS/NZS 4056.1:1992 ISO 5742:1982 Australian Standard ® New Zealand Standard Pliers and nippersPart 1: Nomenclature T h i s i s a f r e e 6 p a g e s a m p l e . A c c e s s t h e f u l l v e r s i o n a t h t t p : / / i n f o s t o r e . s a i g l o b a l . c o m . AS/NZS 4056.1:1992 This Standard was prepared under a joint arrangement by Standards Australia and theStandards Association of New Zealand. It was approved for publication on behalf of theCouncil of Standards Australia on 16 July 1992 and on behalf of the Standards Council of New Zealand on 11 September 1992. It was published on 14 September 1992. The following organisations are represented on the Committees responsible forthis Standard:Standards Australia Committee ME/10, Small Tools AustroadsConfederation of Australian IndustryCSIRO, Division of Manufacturing TechnologyDeakin UniversityDepartment of DefenceFasteners Institute of AustraliaMetal Trades Industry Association of AustraliaN.S.W. TAFE CommissionRailways of Australia CommitteeSociety of Automotive Engineers, AustraliaTelecom AustraliaWorkCover Authority, New South Wales Standards Association of New Zealand Committee 50/-, Mechanical and GeneralBoard Accident Compensation CorporationConsumers InstituteDepartment of LabourDepartment of Scientific & Industrial ResearchInstitution of Professional Engineers of New ZealandMedical AssociationMinistry of CommerceMinistry of TransportNational Council of WomenNew Zealand Chemical Industry CouncilNew Zealand Manufacturers Federation Review of Standards. To keep abreast of progress in industry, Joint Australian/ New Zealand Standards are subject to periodic review and are kept up to date by theissue of amendments or new editions as necessary. It is important therefore thatStandards users ensure that they are in possession of the latest edition, and anyamendments thereto.Full details of all Joint Standards and related publications will be found in theStandards Australia and Standards New Zealand Catalogue of Publications; thisinformation is supplemented each month by the magazines ‘The Australian Standard’and ‘Standards New Zealand’, which subscribing members receive, and which givedetails of new publications, new editions and amendments, and of withdrawnStandards.Suggestions for improvements to Joint Standards, addressed tothe head office of eitherStandards Australia or Standards New Zealand, are welcomed. Notification of anyinaccuracy or ambiguity found in a Joint Australian/New Zealand Standard should bemade without delay in order that the matter may be investigated and appropriate actiontaken. T h i s i s a f r e e 6 p a g e s a m p l e . A c c e s s t h e f u l l v e r s i o n a t h t t p : / / i n f o s t o r e . s a i g l o b a l . c o m . AS/NZS 4056.1:1992 Australian Standard ® New Zealand Standard Pliers and nippersPart 1: Nomenclature First published as Joint StandardAS/NZS 4056.1:1992. PUBLISHED JOINTLY BY:STANDARDS AUSTRALIA1 The Crescent,Homebush NSW 2140 AustraliaSTANDARDS NEW ZEALANDLevel 10, StandardsHouse,155 The Terrace,Wellington 6001 New Zealand ISBN 0 7262 7711 8 T h i s i s a f r e e 6 p a g e s a m p l e . A c c e s s t h e f u l l v e r s i o n a t h t t p : / / i n f o s t o r e . s a i g l o b a l . c o m . 2PREFACE This Standard was prepared by the joint Standards Australia/Standards Association ofNew Zealand Committee on Small Tools. It is identical with and has been reproduced fromISO 5742:1982, Pliers and nippers—Nomenclature and includes Addendum 1:1985.Under arrangements made between Standards Australia, the Standards Association ofNew Zealand and the international Standardsbodies, ISO and IEC, as well as certain otherStandardsorganizations,users of this joint Australian/NewZealand Standard are advised ofthe following:(a) Copyright is vested in Standards Australia, and the Standards Association ofNew Zealand.(b) The number of this Standard is not reproduced on each page; its identity is shown onlyon the cover and title page.(c) Where any cross-references to pagenumbers appearwithin thetext, theserelate to pagenumbering in the InternationalStandard and are to be disregarded.ThisStandardis one of a serieswhich dealwith pliersand nippers for general use, the seriesbeing arranged as follows:AS/NZS 4056.1 Part 1: NomenclatureAS/NZS 4056.2 Part 2: General technical requirementsAS/NZS 4056.3 Part 3: Methods of testAS/NZS 4056.4 Part 4: Pliers for grippingandmanipulating—Dimensionsand testvaluesAS/NZS 4056.5 Part 5: Engineer’s and lineman’spliers—Dimensionsand test valuesAS/NZS 4056.6 Part 6: Lever assisted side cutting pliers, end and diagonal cuttingnippers—Dimensions and test valuesAS/NZS 4056.7 Part 7: End cutting nippers—Dimensions and test valuesAS/NZS 4056.8 Part 8: Diagonal cutting nippers—Dimensionsand test valuesAS/NZS 4056.9 Part 9: Multiple slip joint pliers—Dimensions and test valuesAS/NZS 4056.10 Part 10: Construction worker’s pincers—Dimensions and test valuesAS/NZS 4056.11 Part 11: Carpenter’s pincers—Dimensionsand test valuesAS/NZS 4056.12 Part 12: Slip joint pliers—Dimensionsand test values © Copyright STANDARDS AUSTRALIA/STANDARDS NEW ZEALANDUsers of Standards are reminded that copyright subsists in all Standards Australia and Standards New Zealand publications andsoftware. Except where the Copyright Act allows and except where provided for below no publications or software produced byStandards Australia or Standards New Zealand may be reproduced, stored in a retrieval system in any form or transmitted by anymeans without prior permission in writing from Standards Australia or Standards New Zealand. Permission may be conditional on anappropriate royalty payment. Australian requests for permission and information on commercial software royalties should be directedto the head office of Standards Australia. New Zealand requests should be directed to Standards New Zealand.Up to 10 percent of the technical content pages of a Standard may be copied for use exclusively in-house by purchasersof the Standard without payment of a royalty or advice to Standards Australia or Standards New Zealand.Inclusion of copyright material in computer software programs is also permitted without royalty payment provided suchprograms are used exclusively in-house by the creators of the programs.Care should be taken to ensure that material used is from the current edition of the Standard and that it is updated whenever theStandard is amended or revised. The number and date of the Standard should therefore be clearly identified.The use of material in print form or in computer software programs to be used commercially, with or without payment, or incommercial contracts is subject to the payment of a royalty. This policy may be varied by Standards Australia or StandardsNew Zealand at any time. T h i s i s a f r e e 6 p a g e s a m p l e . A c c e s s t h e f u l l v e r s i o n a t h t t p : / / i n f o s t o r e . s a i g l o b a l . c o m .
