Transcript
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Quickstart Guide Get started in three easy steps Prepare – Read the important information on pages 3, 4, and 5 Identify – Identify – Find your cartridge on the table of contents on pages 6-7 Refill – Follow the directions on the page for your cartridge
Trouble Reading This Manual? www.easyinkjetrefill.com View the full size color manual & updates online or call our Customer Solution Center at 316.618.3500 This manual is copyright 2003-2006 Stratitec, Inc. Stratitec and the Stratitec logo are registered trademarks, and the Stratitec rainbow mark is a trademark of Stratitec, Inc. HP is a registered trademark of Hewlett-Packard Company. Apple is a registered trademark of Apple Computer, Inc. Canon is a registered trademark of Canon, Inc. Epson is a registered trademark of Seiko Epson Corporation. Lexmark is a registered trademark of Lexmark International, Inc. All other trademarks are registered to their respective owners.
060905
Page 2
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Tool Identification and Reference
Screw Tool
3mm Drill Bit
Screw Tool
Plugs
Priming Tips
The screw tool is used to remove plugs and enlarge refill holes.
The drill bit is used to enlarge or create new refill holes. Apply firm firm pressu pressure re when when drilli drilling ng to mini minimi mize ze debr debris is and and to make make Drill Bit drilled holes smooth for a proper seal.
Cartridge Refill Clip*
Cartridge Opening Tool*
Rubber Sealing Pad*
Optional Tools The cartridge refill clip is used to refill and prime HP 15 and 45 style cartridges. It doubles as a primin priming g and evac evacuat uating ing tool for HP 17, 23, 25 and 78 Cartridge color cartridges.
Refill Clip with Rubber Tip*
To assemble, insert the rubber tip into the hole at the base end of the clip.
The small priming priming tip tip is used for priming individual nozzles. It may also be used to create pressure or a vacuum in certain cartridges.
Small Priming Tip
Large Priming Tip
The large priming tip is used to prime print heads and cartridges. It fits on the end of an empty syringe, and can draw draw ink, ink, air, air, or clog clogs s from from the cartridge or print head.
The small plug is for use with the standard 3mm drilled fill hole.
Cartridge Opening Tool*
The cartridge opening tool is used to remove the tops from spe specifi cific c HP and Lex Lexmark color cartridges.
The The rubb rubber er seali ealing ng pad pad is used used to temp tempor orar aril ily y seal seal a Small Plug vent hole or ink outlet. Apply Plugs may come in a sheet the smooth side of the rubber as indi indica cate ted d at left left.. Pull Pull to the surf surfac ace e to be seal sealed ed firmly to remove them for Rubber and maintain pressure with a use. Sealing Pad* thumb or forefinger. The large plug is used for the prepre-e exist isting ing hol holes in som some cartridges. The large plug can also be used to make a tight Large Plug seal *Tools in light gray are seal wh when en a smal smalll plug plug does does included with some refill kits. not seal properly.
www.easyinkjetrefill.com
Page 3
InkJet Refill Kit
InkJet Cartridge Refilling Manual
General Refill Guidelines WHEN USING CUTTING OR DRILLING EQUIPMENT, WEAR SAFETY GOGGLES AND FOLLOW ALL OPERATING AND SAFETY INSTRUCTIONS. KEEP INK OUT OF REACH OF CHILDREN. MAY BE HARMFUL HARMFUL IF SWALLOWED. SWALLOWED. DO NOT NOT INGEST. INGEST. IN CASE CASE OF INGESTION, SEEK IMMEDIATE MEDICAL MEDICAL ATTENTION. AVOID CONTACT WITH SKIN AND EYES. SAFETY INFORMATION AT WWW.STRATITEC.COM. WWW.STRATITEC.COM. Successfully refilling ink cartridges may take some practice, but the process gets easier each time. It is extremely important that tha t you read these refill guidelines and the instructions for your cartridge carefully to ensure desired results and avoid mishaps.
Prepare a Work Area
✔
Refill cartridges in an area that is well-suited for the work.
✔
Ink can spill; place a large sheet of aluminum foil and/or a thick pile of newspaper on your work surface.
✔
Keep distractions to a minimum.
✔
Wear an apron or older clothes in case of a spill, as well as plastic gloves to protect your hands from ink stains.
✔
Clean up immediately with soap and water.
✔
Ink on hands or arms will wash off in a few days. Do not refill over carpeted areas or near fine furniture.
Prepare Ink and Syringes
Do Not Remove Seals
Page 4
✔
Syringe size and style may vary. Always use a syringe with a locking tip where specified.
✔
Always check to be sure that the needle or tip is securely attached to the syringe.
✔
Do not fill syringe with ink until you are ready to refill your cartridge.
✔
Unused ink may be returned to the appropriate ink bottle or stored in the syringe. Be sure to secure a rubber scabbard to each needle tip to prevent leaking or drying out.
✔
Label the syringe(s) to easily identify the ink color.
✔
Thoroughly rinse and dry needle and syringe when changing ink colors.
✔
Do not remove the bottle seals.
✔
Use a needle or the screw tool to create a small hole in the seal and draw ink through the hole in the seal.
✔
To avoid accidental spills, replace the bottle caps promptly.
Free Technical Support at 316.618.3500
InkJet Refill Kit Use Recently Emptied Cartridges
Know The Colors Cyan (Blue/Green)
InkJet Cartridge Refilling Manual
Old and/or dry cartridges may not work, even after refilling, priming and cleaning. ✔
Refill your cartridges just before or immediately immediately after they run out of ink.
✔
Cartridges should not be stored outside of your printer for more than an hour unless required required as part of the refill process.
✔
Ink in the ink supply outlets or print heads will dry out in cartridges that are stored improperly, or allowed to remain empty for long periods of time, and refilling such cartridges may not be successful.
✔
Color printers require special ink colors to produce high-quality prints. Standard color printers require color blends known as cyan (blue/green), magenta (red/purple), and yellow.
✔
Many inkjet printers can use “photo” cartridges, which require two additional colors: “photo cyan” or light cyan and “photo magenta” or light magenta. Printers that require these additional photo cartridges are called “six-color” printers.
Magenta (Red/Purple) Yellow (Yellow)
Photo cyan and photo magenta inks are only for six-color printers. They are not intended for use in standard four-color printers, even when printing photos. If photo cyan and/or photo magenta are used in a standard four-color four-color printer, the color balance will be incorrect and the quality will be reduced.
Photo Cyan (Light Cyan) Photo Magenta (Light Magenta)
Use Colors Correctly
Injecting the wrong color of ink into the ink chamber of a color cartridge will cause unfavorable results and may ruin your cartridge. ✔
Use care when refilling color cartridges. Always inject the correct color of ink into the correct ink chamber.
✔
To verify the color of ink contained in each chamber of the cartridge, insert a wooden toothpick into each refill hole, withdraw it, and then check the color of the toothpick.
Avoid overfilling
Overfilled cartridges may leak and cause color contamination. ✔
Overfilled cartridges will not print. Use care to avoid overfilling!
✔
Use only enough ink to fill the cartridge.
✔
If you do overfill your cartridge, refer to the instructions for your cartridge and use a syringe to extract excess ink. Never install a cartridge that is leaking, dripping, or oozing ink. Doing so may damage your printer.
www.easyinkjetrefill.com
Page 5
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Instructions by Cartridge Apple® M1949..........................................18 M1950..........................................18 M1951..........................................18 M1952..........................................18 M3240..........................................19 M3329..........................................20 M3330..........................................20 M3822..........................................18 M3852..........................................18 M3908..........................................20 M3909..........................................20 M3910..........................................20 M3911..........................................20 M3912..........................................20 M4609..........................................21 M5658............................................8 M5659............................................8 M5693..........................................12 M5694..........................................11 M8041..........................................21 M8049..........................................21 M8052..........................................21
Brother® IN-700...........................................16 IN-710C........................................17 IN10..............................................21 LC02BK/C/Y/M..............................26 LC04BK/C/Y/M..............................26 LC11-BK........................................16 LC11-CL........................................17 LC21BK/C/Y/M..............................26 LC31BK/C/Y/M..............................26 LC41BK/C/Y..................................22
Canon® BC-01............................................21 BC-02............................................21 BC-05............................................21 BC-06............................................21 BC-20............................................19 BC-23............................................19 BC-30/BC-30e...............................18 BC-31/BC-31e...............................18 BC-33e..........................................18 BC-60............................................27 BCI-10...........................................20 BCI-11...........................................20 BCI-15...........................................20 BCI-21...........................................20 BCI-24...........................................20 BCI-3Bk/BCI-3eBk........................18 BCI-3C/BCI-3eC............................18 BCI-3M/BCI-3eM..........................18 BCI-3PC/3PM................................18 BCI-3Y/BCI-3eY............................18 BCI-5Bk........................................18 BCI-5C/BCI-5M/BCI-5Y................18 BCI-61...........................................27 BCI-61e.........................................27
BCI-62.......................................27 BCI-62e.....................................27 BCI-6Bk.....................................18 BCI-6C/BCI-6M/BCI-6Y.............18 BCI-6G......................................27 BCI-6PC/BCI-6PM.....................18 BCI-6R......................................27 BCI-8Bk.....................................18 BCI-8C/BCI-8M/BCI-8Y.............18 BJI-201Bk(HC)..........................18 BJI-201C/BJI-201M/BJI-201Y....18 BX-2..........................................21 BX-20........................................19 CL-40........................................27 CL-41........................................27 CLI-8BK....................................18 CLI-8C.......................................18 CLI-8M......................................18 CLI-8PC.....................................18 CLI-8PM....................................18 CLI-8Y.......................................18 PG-40........................................27 PG-41........................................27 PGI-5.........................................18
Compaq® 180844-001...............................17 180845-001...............................16 180846-001...............................17 180847-001...............................16 180848-001...............................17 203428-001...............................16 337709-001...............................16 337710-001...............................17 337711-001...............................17 337714-001...............................16 337715-001...............................17
Dell® 7Y743/X0502 (A940/A960).......14 7Y745/X0504 (A940/A960).......15 J4844/K5553 (922/942/962).....15 J5566/R5956 (922/942/962).....14 J5567/R5974 (922/942/962).....15 M4640/R5480 (922/942/962)...14 M4646/R5482 (922/942/962)...15 T0529/K101 T0529/K1014 4 (720/920)...........14 (720/920)...........14 T0530/K1017 (720/920) ...........15 T0601/K1143 (J740).................14 T0602/K1145 (J740).................15
Epson® S020034....................................23 S020036....................................23 S020047....................................23 S020049....................................23 S020062 (K)..............................27 S020089....................................23 S020093....................................23 S020097....................................23 S020108....................................23 S020118 (K)..............................27
S020122 (Y)..................................27 S020126 (M).................................27 S020130 (C).................................27 S020138.......................................23 S020143 (M).................................27 S020147 (C).................................27 S020187.......................................23 S020189.......................................23 S020191.......................................23 S020193.......................................23 T001 (T001011)............................23 T003 (T003011)............................23 T005 (T005011)............................23 T007* (T007201)..........................23 T008* (T008201)..........................23 T009* (T009201)..........................23 T013 (T013201)............................23 T014 (T014201)............................23 T015* (T015201)..........................23 T016* (T016201)..........................23 T017* (T017201)..........................23 T018* (T018201)..........................23 T019 (T019201)............................23 T020 (T020201)............................23 T026* (T026201)..........................23 T027* (T027201)..........................23 T028* (T028201)..........................23 T029* (T029201)..........................23 T036* (T036120)..........................23 T037* (T037020)..........................23 T038* (T038120)..........................23 T039* (T039020)..........................23 T040* (T040120)..........................23 T041* (T041020)..........................23 T0431* (T043120)........................24 T0441* (T044120)........................24 T0442* (T044220)........................24 T0443* (T044320)........................24 T0444* (T044420)........................24 T0481* (T048120)........................24 T0482* (T048220)........................24 T0483* (T048320)........................24 T0484* (T048420)........................24 T0485* (T048520)........................24 T0486* (T048620)........................24 T0601* (T060120)........................24 T0602* (T060220)........................24 T0603* (T060320)........................24 T0604* (T060420)........................24 T480 (T480011)............................27 T481 (T481011)............................27 T482 (T482011)............................27 T483 (T483011)............................27 T484 (T484011)............................27 T485 (T485011)............................27
Hewlett-Packard® 51625 51626 51629 51633
(25)....................................11 (26)....................................12 (29)....................................12 (33)....................................12
* Ink is compatible with these cartridges, but they may require an ink-level chip reset to print. See page 25 page 25 for for details. ** These cartridges may require a third party replacement chip and resetter. See page 31 for details. Note: Many HP cartridges have additional letters following the part number. For example, the C6615 may be marked C6615N, C6615AN or C6615DN. All cartridges are compatible, regardless of the extra letters after the part number.
Page 6
Free Technical Support at 316.618.3500
InkJet Refill Kit 51640a (40)....................................8 51640c (40)....................................8 51640m (40)...................................8 51640y (40)....................................8 51641 (41)......................................9 51644c/51644m/51644y (44).........8 51645a (45)....................................8 51645c (45)....................................8 51645m (45)...................................8 51645y (45)....................................8 51649 (49)....................................11 51650c/51650m/51650y (50).........8 C1816 (16)....................................11 C1823 (23)......................................9 C3844A (844).................................9 C3845A (845).................................9 C4836 (11)**................................27 C4837 (11)**................................27 C4838 (11)**................................27 C4841 (10)**................................27 C4842 (10)**................................27 C4843 (10)**................................27 C4844 (10)**................................27 C5010AN (14)...............................13 C5011AN (14)...............................13 C6578 (78)......................................9 C6614 (20)....................................12 C6615 (15)......................................8 C6625 (17)......................................9 C6628 (19)....................................12 C6634 (34)....................................11 C6635 (35)....................................11 C6656 (56)....................................10 C6657 (57)....................................10 C6658 (58)....................................10 C8727 (27)....................................10 C8728 (28)....................................10 C8765 (94)....................................10 C8766 (95)....................................10 C8767 (96)....................................10 C9351 (21)....................................10 C9352 (22)....................................10 C9359 (59)....................................27
C9361 C9362 C9363 C9368 C9369
InkJet Cartridge Refilling Manual (93)................................10 (92)................................10 (97)................................10 (100)..............................27 (99)................................10
Lexmark® 10N0016 (16)............................14 10N0026 (26)............................15 10N0217 (17)...........................14 10N0227 (27)...........................15 10N0510/10N610.....................15 10N500/10N600.......................14 12A1970 (70)............................16 12A1975 (75)............................16 12A1980 (80)............................17 12A1985 (85)............................17 12A1990 (90)............................17 13400HC...................................16 1361400....................................16 1361760....................................17 13619HC...................................17 13620HC...................................16 1380619....................................17 1380620....................................16 1381400....................................16 1382050....................................16 1382060....................................17 15M0120 (20)...........................17 15M0125 (25)...........................17 15M2971 (71)...........................16 16G0055 (55)............................16 16G0065 (65)............................17 17G0050 (50)............................16 17G0060 (60)............................17 18C0031 (31)............................15 18C0032 (32)............................14 18C0033 (33)............................15 18C0034 (34)............................14 18C0035 (35)............................15 18C0500...................................14 18C0510...................................15 18C0520...................................15
18C0690.......................................14 18C0700.......................................15 18C0781 (1)..................................15 18L0032 (82)................................14 18L0042 (83)................................15 18L0380.......................................14 18L0390.......................................15 18L0500/18L0590........................14
Misc Cartridge Top Removal.................32 Check / Correct Overfill................33 Color Cartridge Troubleshooting. Troubleshooting. .28 General Cartridge Priming...........30 HP Cartridge Priming...................29 Ink-level Chip Reset Details..........25 Troubleshooting Troubleshooting Table............... ...35
Okidata® 52109301......................................16 52109302......................................17
Olivetti® 84431............................................16 84433............................................16
Sharp® AJ-C50B........................................16 AJ-C50C........................................17 FO-C60B.......................................14 UX-22BC.......................................16 UX-27CC.......................................17 UX-C70B.......................................14
Sony® IJC-B1...........................................12 IJC-C1...........................................11
Xerox® 8R12591.......................................17 8R7879.........................................16 8R7880.........................................17 8R7881.........................................16 8R7882.........................................17 8R7903.........................................14 8R7904.........................................15
Trouble Reading This Manual? www.easyinkjetrefill.com View the full size color manual & updates online or call our Customer Solution Center at 316.618.3500 (Instructions for cartridges not listed may be available online) Note: Many HP cartridges have additional letters following the part number. For example, the C6615 may be marked C6615N, C6615AN or C6615DN. All cartridges are compatible, regardless of the extra letters after the part number.
www.easyinkjetrefill.com
Page 7
InkJet Refill Kit Recommended Tools
Remove black tape or plug to access the ink fill hole
InkJet Cartridge Refilling Manual
Hewlett Packard: 51640a/51640c/51640m/51640y (40) •51645a/51645c/51645m/51645y •51645a/51645c/51645m/51645y (45) •51644c/51644m/51644y •51644c/51644m/51644y (44)•51650c/51650m/51650y (44)•51650c/51650m/51650y (50) •C6615 (15) Apple: M5658•M5659 M5658•M5659 (Suffix may vary) vary) 1.
Read pages 4-5 in the manual manual for for importa important nt general general informa information tion that that will improve your results. If your kit includes the cartridge refill clip tool, you may optionally follow the instructions under “Refilling “Refilling with the Clip Tool“ Tool“ on page 29 to refill your HP 15 or 45 cartridge. Before Before refillin refilling, g, turn the cartrid cartridge ge upside upside down down and and remove remove the black black tape (or plug) covering the fill hole.
3.
If this this is the the first first time refilling refilling the cartr cartridge, idge, you you will will find a stainl stainless ess steel ball bearing in the fill hole as shown in the diagram. Push the ball empty syringe (without bearing into the cartridge using the tip of an empty syringe the needle). Be very gentle in the following steps when inserting the needle into the cartridge. If the ink bag is damaged, the cartridge can no longer be used.
Use the tip of an empty syringe to push the ball bearing into the cartridge.
After refilling is complete, squeeze the sides of the cartridge as you insert the large plug into the fill hole.
Page 8
2.
4.
Fill the syring syringe e with ink and and inject inject into into the fill fill hole. hole. Repeat Repeat until until bubbles appear at the fill hole.
5.
In order order to seal seal the fill fill hole, hole, you must must firmly firmly squeeze squeeze the cartridg cartridge e sides and put a large plug into the hole. (Squeezing the cartridge while the plug is inserted creates back pressure that helps stop the ink from leaking out when refilling is completed.)
6.
Some ink ink may drip from the print print head. head. Place Place the the cartridg cartridge e in a sink sink or or pan for 1-2 minutes with the print head down. Gently wipe the print head with a paper towel. Hold the cartridge up so the print head is down, and look at the print head. If you see any liquid ink, the cartridge is not properly pressurized pressurized and is leaking. Repeat the t he previous step.
7.
Place Place the cartrid cartridge ge into your printer printer and and run run test/clean test/cleaning ing cycles cycles as as described described in your printer manual. Please read Resetting Ink Levels to reset your printer's ink level counters. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com www.easyinkjetrefill.com
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
Hewlett-Packard: 51641 (41)•C1823 (23)•C3844A (23)•C3844A (844) C3845A (845)•C6578 (78)•C6625 (17) 1.
Read pages 4-5 for for importa important nt general general informa information tion that that will improve improve your results.
2.
Locate Locate the plugs plugs (actual (actual plug plug positions positions may vary) vary) on the top of of the cartri cartridge dge and use the screw tool to push the plugs through the refill holes and into the cartridge. Leave the plugs in the cartridge. If your cartridge does not have plugs, or if you are unable to push the plugs into the cartridge, then drill refill holes where indicated at left.
3.
Verify Verify the ink ink colors colors in each each chamber chamber (see (see “Use “Use Colors Colors Correctly Correctly” ” on page 5). Do NOT rely solely upon cartridge label colors.
4.
Select the color to to be refilled refilled and and fill fill a syringe syringe with with ink. Place Place tape tape over the the remaining refill holes to prevent cross-contamination. TAPE MUST BE REMOVED BEFORE CARTRIDGE IS REINSTALLED OR CARTRIDGE WILL NOT PRINT.
5.
Carefully Carefully inser insertt the needle needle into into the correct correct refill refill hole hole until until the needle needle tip is is halfway into the foam sponge, then position the cartridge horizontally as indicated below, right.
6.
Slowly inject Slowly inject up to 10ml of ink. Injecting ink too quickly may trap air inside the cartridge. As you add ink, watch the print head closely. If ink begins to come out of the print head or around the refill hole, stop filling, then use the syringe to extract 1ml of ink.
7.
Leave the the cartridge cartridge in the the horizon horizontal tal position position as indica indicated ted below. below. Repeat Repeat steps 4-6 to fill each color in the cartridge.
8.
Verify Verify ink flow flow by pressi pressing ng the print print head head against against a damp damp paper paper towel. towel. Each color should leave a solid line on the towel. If some ink colors are not visible, follow the cartridge priming instructions on page 29. 29.
Magenta Cyan Yellow
51641 • C1823 C6578 • C6625 Photo Cyan Black
Cyan
This cartridge is easy to overfill. Check / correct overfilling by following t he instructions on page 33. 33.
C3845A (845) Photo Magenta Yellow
InkJet Cartridge Refilling Manual
9.
Re-install Re-install the the cartridge cartridge,, run cleani cleaning ng cycles, cycles, and print print test test pages. pages. To reset reset ink levels, please refer to the section on “Resetting Ink Levels” on page 31. 31. If print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” on page 28. 28.
Magenta For best results, refill cartridges before before they are empty. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
C3844A (844)
REFILL HOLES MUST STAY OPEN. REMOVE TAPE AFTER FILLING. DO NOT PLUG HOLES.
www.easyinkjetrefill.com
Stop filling if ink drips from print head.
Position cartridge as shown to inject ink.
Page 9
InkJet Refill Kit Recommended Tools
Refill holes
InkJet Cartridge Refilling Manual
HP: HP: C6656 (56)•C6657 (57)•C6658 (58)•C8727 (27)•C8728 (28) C8765 (94)•C8766 (95)•C8767 (96)•C9351 (21)•C9352 (22)• C9361 (93)•C9362 (92)•C9363 (97)•C9369 (99) 1.
Read pa pages 4-5 for important general information that will improve your results.
2.
Remove Remove the sticker sticker from from the the top of the the cartridg cartridge e to expose expose the refill refill holes. holes.
3.
Select Select the color to be refilled refilled and and fill a syringe syringe with with ink. ink. Place tape tape over the remaining refill holes to reduce the risk of color cross-contamination.
4.
With the the cartridg cartridge e upright, upright, carefully carefully inser insertt the needle needle into into the correc correctt refill hole until the needle tip is halfway into the cartridge as indicated at left.
5.
Slowly inject Slowly inject up to 5ml of ink (2ml for 22 and 93) per chamber if refilling a color cartridge, or up to 20ml of ink (5ml for 21 and 92) if refilling a black cartridge, into the appropriate refill hole for your cartridge, as indicated below. Injecting ink too quickly may trap air inside the cartridge. As you add ink, watch the print head closely. I f ink begins to come out of the print head or around the refill hole, stop filling, then use the syringe to extract 0.5ml of ink.
6.
Refill Refill each each color by by repeating repeating the above above proces process, s, making making sure sure to tape tape over the the unused refill holes to prevent contamination.
7.
Verify Verify ink ink flow by press pressing ing the the print head head against against a damp damp paper paper towel. towel. Each color should leave a solid line on the towel. If not all ink colors are visible, follow the priming instructions on page 30. 30. This cartridge is easy to overfill. Check / correct overfilling by following the instructions on page 33. 33.
Insert needle about halfway into the cartridge and slowly inject ink
8.
Remove Remove any tape tape covering covering the refill refill holes holes and and replace replace the origin original al sticker. sticker. Reinstall the cartridge, run cleaning cycles, and print test pages. If print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” Troubleshooting” on page 28. 28.
9.
Ink levels levels are are estimated estimated by by the printer printer base based d on the the amount amount of printing printing that that has been done. Consequently, Consequently, the printer may report the cartridge as empty, even when completely refilled. Ignore the low ink messages and continue printing. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
(22, 28, 57) Magenta (93, 95, 97) Yellow
(22, 28, 57) Yellow (93, 95, 97) Magenta
Page 10
(21, 27, 56, 92, 94, 96) Black
(22, 28, 57, 93, 95, 97) Cyan
(58) Photo Magenta (99) Black
(58) Black (99) Photo Magenta
(58, 99) Photo Cyan
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
Hewlett-Packard: 51625 (25)•51649 (49)•C1816 (16)•C6634 (16)•C6634 (34)•C6635 (35) Apple: (35) Apple: M5694 Sony: IJC-C1
First refill requires top removal (see page 32 for alternate methods)
1.
Read pages 4-5 for important general information that will improve your results.
2.
If this is the the first first refill, refill, the cartri cartridge dge top must must be remov removed. ed. Some Some kits may may include a top removal tool (shown left). left). Please review review “Cartridge Top Removal” instructions and “Alternate Removal Methods” on page 32. 32. If you need a top removal tool, please see www.easyinkjetrefill.com. www.easyinkjetrefill.com.
3.
When removing removing the the top, be be careful careful not not to damage damage the the black black tab, located located near the lid, as this is required to securely reinstall reinstall the cartridge in the printer.
4.
Select the the color color to to be refille refilled d and and fill fill a syrin syringe ge with with ink. ink.
5.
With the the cartridge cartridge upright upright,, carefully carefully insert insert the the needle needle into into the correct correct chamber (as indicated below, left), until the tip of the needle is halfway into the foam sponge. Do NOT push the needle all the way to the bottom.
6.
Slowly inject Slowly inject up to 8ml of ink into the appropriate chamber for your cartridge. Injecting ink too quickly may trap air inside the cartridge. As you add ink, watch the sponge surface closely. The original color of the sponge is white. Stop filling as soon as as you see the ink start to come up around the needle or edges. edges. If possible, possible, do NOT allow the color of the sponge to change. If ink appears on on the surface of the sponge, stop filling, filling, then use the syringe to extract 0.5-1ml of ink. Refill each color by repeating the above process, keeping the cartridge upright.
7.
Verify Verify ink flow flow by pressi pressing ng the print print head head against against a damp damp paper paper towel. towel. Each color should leave a solid line on the towel. If all ink colors are not visible, or if one or more colors are faint, follow the priming instructions on page 30. 30.
8.
Once the the cartridge cartridge is refilled, refilled, tape tape the cartri cartridge dge top secur securely ely in place. place.
9.
Re-install Re-install the cartr cartridge, idge, run run cleaning cleaning cycles, cycles, and and print print test pages. pages. If print print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” on page 28. 28.
Top may detach in two different ways HP 25, 34, 35, 49 Apple M5694
Sony IJC-C1
e d i s l e b a l
Cyan Yellow Magenta
HP 16
InkJet Cartridge Refilling Manual
e d i s l e b a l
These cartridges dry out easily when unused, even if filled with ink. As the cartridge dries out, the ink in the bottom chambers becomes very thick and is almost impossible impossible to remove, even after refilling with fresh ink. For best results, don't allow these cartridges to sit unused for long periods of t ime. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com www.easyinkjetrefill.com
Photo Cyan Photo Black Magenta
www.easyinkjetrefill.com
Page 11
InkJet Refill Kit Recommended Tools
NOT a fill hole
InkJet Cartridge Refilling Manual
Hewlett Packard: 51626 (26)•51629 (29)•51633 (33)•C6614 (20) C6628 (19) Apple: (19) Apple: M5693 Sony: IJC-B1 1.
Read pages 4-5 for important general information that will improve your results.
2.
Place the cartri cartridge dge on on thickly thickly folded folded paper towels. towels. Ink may may begin begin to drip from the cartridge after opening the refill hole and while injecting ink.
3.
Old cartrid cartridges ges may may have a refill refill hole hole on the the top corner corner that that is sealed sealed by by a ball bearing. If you have an old cartridge, push the ball bearing into the cartridge. Take care not to damage the print head by pressing it too hard against the work surface. If your cartridge does not have a refill hole with a ball bearing, use a 3mm drill bit to make a refill hole where indicated at left. The hole that is located in the center of the cartridge top is NOT a fill hole. Inserting any object or fluid into this hole may damage t he ballast bags and render the cartridge unusable.
Drill Refill Hole Here (Push in ball bearing on old cartridges)
Vent Maze
Outlet Hole
Align tip with vent maze outlet hole. Pull 3-4 ml of air, bubbles or ink out.
4.
Fill a syrin syringe ge with the the appropri appropriate ate color of ink and, and, with with the cartrid cartridge ge upright, upright, carefully insert the needle into the refill hole and quickly fill the cartridge until it is almost full (25-40ml). Expect ink to begin dripping dripping from the the bottom.
5.
Once the the cartridg cartridge e is refilled refilled,, promptly promptly seal the the refill refill hole with with a rubber rubber plug. Do not use tape. The seal must be airtight or the cartridge will leak.
6.
Turn the the cartridg cartridge e upside upside down down to expose expose the vent vent maze. maze. Attach the the small small priming tip (page 3) onto an empty syringe and put the tip of the syringe into the outlet hole of the vent maze.
7.
Pull back back on the syrin syringe ge to withdra withdraw w 3-4 ml ml of air, air, bubbles bubbles and/o and/orr ink from from the cartridge. The pressure pressure in the cartridge should now be be properly balanced.
8.
Wipe the the cartridge cartridge with with a damp damp paper towel. towel. Hold Hold the cartr cartridge idge in an an upright upright position for 30 30 seconds and look closely at the bottom. If you see ink seeping from the print head or vent maze outlet hole, you must verify that the refill hole is sealed properly and repeat steps 6 - 8. The process should be repeated repeated until the cartridge no longer seeps, indicating that the pressure is equalized. equalized.
9.
Verify Verify ink flow flow by pressi pressing ng the print print head head against against a damp damp paper paper towel. towel. The print head should leave a solid black li ne on the damp towel. If you don't see a solid black line, follow the priming instructions on page 30. 30.
10. Wait approximately 2 minutes, minutes, then follow step 8 again as a final final check that the cartridge is not leaking. Re-install the cartridge, run cleaning cycles, and print test pages. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Page 12
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
Hewlett-Packard: C5010AN (14)•C5011AN (14) 1.
2.
Place the the cartridge cartridge with with the ink ink outlet(s) outlet(s) facing facing up, up, as indicat indicated ed at left, left, on a flat, ink-resistant surface or on paper towels or absorbent cloth in case of spills or leakage.
3.
Select color color to be be refilled refilled and and fill a syrin syringe ge with ink, ink, then then carefull carefully y remove the the needle and attach the small priming tip (page 3).
4.
Gently Gently press the priming priming tip tip against against the appropri appropriate ate ink outlet, outlet, as indicated indicated below left, and slowly inject slowly inject up to 6ml of color ink or up to 23ml of black ink. It is important not to t o dent, mar, or damage the sponge when refilling or the cartridge will be unusable. Stop filling when the sponge is full and stops absorbing absorbing ink quickly. A dry sponge may absorb ink more slowly.
5.
Carefully Carefully turn turn the cartr cartridge idge to the the upright upright position, position, using using a paper paper towel towel or absorbent absorbent cloth to absorb any ink dripping from the ink outlet. Hold cartridge upright until ink no longer drips from the ink outlet. Installing the cartridge while ink is still dripping and/or leaking out of the cartridge may damage your printer.
6.
Re-install Re-install the the cartridge, cartridge, run run cleanin cleaning g cycles, cycles, and print print test test pages. pages. If print print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” on page 28. 28.
7.
Most printe printers rs that that use the the HP 14 14 cartridge cartridge must either either have the ink-level monitor disabled, or have the ink-level chip replaced in order to use refilled cartridges. Instructions for disabling disabling the ink counter may be in your printer manual. Additional details are online at www.easyinkjetrefill.com.
Magenta Yellow
Refill by gently pressing the small priming tip against the sponge and slowing injecting ink.
Read pages 4-5 for important general information that will improve your results. Check to verify that your cartridge has not exceeded its expiration date. Printers that use the HP14 cartridge are unable to use expired cartridges unless the ink-level ink-level chip is replaced. See www.easyinkjetrefill.com www.easyinkjetrefill.com for details.
Black
Cyan
InkJet Cartridge Refilling Manual
If you disable the ink-level monitor, you MUST NOT let the cartridge run dry. A dry cartridge may cause air bubbles to form in the printhead, stopping the printhead from working properly. Refill frequently frequently and refill immediately if you see a reduction in print quality quality or one of the colors stops printing. For best results, we recommend replacing replacing the ink level chip with a resettable chip and using a chip resetter after each refill to reduce the chance of the cartridge running dry. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Ink-level Chip
www.easyinkjetrefill.com
Page 13
InkJet Refill Kit Recommended Tools
Enlarge the vent hole or remove the label to access fill holes
Lexmark : 10N0016 (16)•10N0217 (17)•10N500/10N600•18C0032 (32)•18C0034 (34)•18C0500•18C0690•18L0032 (82)•18L0380 •18L0500/18L0590 Dell: 7Y743/X0502 (A940/A960)•J5566/R5956 (922/942/962)•M4640/R54 (922/942/962)•M4640/R5480 80 (922/942/962)•T0601/K1143 (922/942/962)•T0601/K1143 (J740)•T0529/K1014 (J740)•T0529/K1014 (720/920) Sharp: UX-C70B•FO-C60B Xerox: 8R7903 1.
Read pa pages 4- 5 for important general information that will improve your results.
2.
Some cartri cartridges dges have a hard hard top, top, while while others others have have a flat top with with a sticker sticker.. For cartridges cartridges with a sticker, simply peel it back to reveal the fill holes. Cartridges with a hard top must have a hole drilled in the top of the cartridge with a 3mm drill drill bit. Drill all the way through the plastic top.
3.
Fill a syringe syringe with with black ink. ink. With the cartridg cartridge e upright, upright, careful carefully ly insert insert the needle into the refill hole, as indicated below, left, until the needle tip is about halfway into cartridge.
4.
Slowly inject Slowly inject ink into the cartridge. Injecting ink too quickly may trap air inside the cartridge. Amount of ink needed varies by cartridge and depends on how empty the cartridge is before refilling. Fill until ink appears at the fill hole, then remove 1ml from the cartridge near the surface of the fill hole.
5.
Verify Verify ink ink flow by press pressing ing the the print head head against against a damp damp paper paper towel. towel. The print head should leave a solid black line on the towel. If ink is not visible, follow the priming instructions on page 30. 30.
Use any of these holes to fill this cartridge with black ink.
This cartridge is easy to overfill. After filling, drain excess ink by placing the cartridge upside-down in a sink on a thickly folded stack of paper towels. When ink stops draining from the cartridge, check / correct any remaining overfill condition by following the instructions on page 33. 33. 6.
Insert the needle about halfway into the cartridge.
InkJet Cartridge Refilling Manual
Re-install Re-install the the cartridge, cartridge, run cleani cleaning ng cycles, cycles, and print print test pages. pages. If print print results are unsatisfactory, unsatisfactory, the cartridge may be overfilled. Remove an additional 1-2ml of ink and try again. For best results, refill cartridges before they are empty. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Empty Chamber
Some Cartridges contain an empty chamber, as shown.
Lexmark 10N0217 (17) Sharp UX-C70B
This chamber may accidentally fill with ink. To correct this, do not remove the l id. Drill a hole directly above the empty chamber, completely drain the chamber of ink, and plug the hole with the small rubber plug. Drill, drain and plug here
Page 14
If excess ink remains in this chamber, the used cartridge may seem full when it is not.
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
Pry the lid off with a small screwdriver here.
Drill holes in the top to access chambers.
Peel the label back to access fill holes.
InkJet Cartridge Refilling Manual
Lexmark: 10N0026 (26)•10N0227 (27)•10N0510/10N610 18C0031 (31)•18C0033 (33)•18C0035 (33)•18C0035 (35)•18C0510•18C (35)•18C0510•18C0520 0520 18C0700•18C0781 18C0700•18C0781 (1)•18L0042 (1) •18L0042 (83)• 18L0390 Dell: 7Y745/X0504 (A940/A960) (A940/A960) J5567/R5974 (922/942/962)•J4844/K5553 (922/942/962)•J4844/K5553 (922/942/962) M4646/R5482 M4646/R5482 (922/942/962)•T0530/K1017 (922/942/962)•T0530/K1017 (720/920) •T0602/K1145 (J740) Xerox : 8R7904 1.
Read pa pages 4-5 for important information that will improve your results.
2.
Before Before refillin refilling, g, the label label or top should should be removed removed or or holes must must be drilled drilled.. Verify the ink colors in each chamber (see “Use Colors Correctly” on page 5), then select the first color to be refilled and fill a syringe with ink. Place tape over the remaining refill holes to prevent cross-contamination.
3.
With the the cartridg cartridge e upright, upright, carefull carefully y insert insert the needle needle into into the corre correct ct refill refill hole until the needle tip is about halfway into the cartridge.
4.
Slowly inject Slowly inject ink into the chamber of the chosen ink color. Injecting ink too quickly may trap air inside the cartridge. Amount of ink needed varies by cartridge and depends on how empty the cartridge is before refilling. Fill until ink appears at the fill hole, then remove 1ml.
5.
Refill Refill each each color by by repeating repeating the above proces process, s, making making sure sure to tape tape over the the unused refill holes to prevent cross-contamination.
6.
Verify Verify ink ink flow by press pressing ing the the print head head against against a damp damp paper paper towel. towel. Each color should leave a solid line on the towel. If not all ink colors are visible, follow the priming instructions on page 30. 30. This cartridge is easy to overfill. Check / correct overfilling by following the instructions on page 33. 33.
7.
Once the cartr cartridge idge is refilled, refilled, remove remove any tape coverin covering g the refill refill holes. holes. If you you removed the top, tape the cartridge top securely back into position.
8.
Re-install Re-install the cartridge, cartridge, run run cleaning cleaning cycles, cycles, and and print print test test pages. pages. If print print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” on page 28. 28. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Lex 26/27 • Dell T0530
Magenta
Peel off the label, or drill through the top above the holes as shown to access the ink chambers. Remove tape when done. Do not overfill.
Cyan
Lex 1/33/35/83 • Dell T0602 7Y745/M4646/J5567
Y e l l o w
Color locations may vary Always check color by inserting a toothpick before injecting ink.
www.easyinkjetrefill.com
Yellow Cyan
M a g e n t a
Photo Magenta
Photo Cyan
Xerox 8R7904
Yellow Magenta
B l a c k
C y a n
Lex 31 Dell J4844
Page 15
InkJet Refill Kit Recommended Tools
Enlarge refill hole
InkJet Cartridge Refilling Manual
Lexmark: 13400HC•1361400•13620HC•1380620• 1381400•1382050•17G0050 1381400•1382050• 17G0050 (50)•16G0055 (50)•16G0055 (55)•12A1970 (70)•15M2971 (71)•12A1975 (75) Compaq: 180845-001 180847-001•203428-001•3 180847-001•203428-001•337709-001• 37709-001• 337714-001•203428-001 337714-001•203428-001 Brother: IN-700•LC11-BK Okidata: IN-700•LC11-BK Okidata: 52109301 Xerox: 8R7879 8R7881 Sharp: AJ-C50B•UX-22BC Olivetti: 84431•84433 1.
Read pa pages 4-5 for important general information that will improve your results.
2.
Enlarge Enlarge the small small hole hole on the top top of the cartr cartridge idge with with the included included screw screw tool or remove the plug.
3.
Select Select the color to be refilled refilled and and fill a syrin syringe ge with ink. ink. With With the cartrid cartridge ge upright, carefully insert the needle into the refill hole until the needle tip is halfway into the foam sponge.
4.
Slowly inject Slowly inject ink into the cartridge. As you add ink, watch the print head closely. If ink begins to come come out of the print head or around the refill refill hole, stop filling. Amount of ink needed varies by cartridge and depends on how empty the cartridge is before refilling. Fill until ink comes out the fill hole, then remove 1ml.
5.
Verify Verify ink ink flow by press pressing ing the the print head head agains againstt a damp paper paper towel. towel. The print head should leave a solid black line on the towel. If ink is not visible, follow the priming instructions on page 30. 30.
Remove Plug
This cartridge is easy to overfill because you cannot see the internal sponge. Overfilling can cause this cartridge to print poorly, not print at all, print only on part of the page, or stop printing after the printer sits idle for a day or two. Check / correct overfilling by withdrawing a few ml of ink, or following the instructions on page 33. 33. 6.
Re-install Re-install the cartri cartridge, dge, run run cleaning cleaning cycles, cycles, and and print print test pages. pages. If If print print results are unsatisfactory, unsatisfactory, the cartridge may be overfilled. Remove 2-4ml 2- 4ml of ink and try again. Do not attempt to print with this cartridge when it is empty as this could damage the print head. For best results, refill cartridges before they are empty.
Cartridge is easy to overfill. See page 33 for help.
Page 16
If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
Lexmark: 12A1980 (80)•12A1985 (85)•12A1990 (90)•1361760 13619HC•1380619•1382060•15M0120 13619HC•1380619•1382 060•15M0120 (20)•15M0125 (25) 16G0065 (65)•17G0060 (60) Okidata: 52109302 Compaq: 180844-001•180846-00 180844-001•180846-001•180848-001•3 1•180848-001•337710-001 37710-001 337711-001•337715-001 Brother: IN-710C•LC11-CL Xerox : 8R12591•8R7880•8R7 8R12591 •8R7880•8R7882 882 Sharp: AJ-C50C•UX-27CC 1.
Glue Seam Some kits may include a top removal tool, as shown. When using the tool, the top may crack as indicated above, or at glue seam. Either result will allow access to the refill holes. For top removal methods with or without the tool, see page 32 32..
InkJet Cartridge Refilling Manual
Read pa pages 4- 5 for important general information that will greatly improve your results.
2.
If this this is the the first first refill, refill, the cartri cartridge dge top must must be remove removed. d. Some Some kits may may include a top removal tool (shown left). Please review top removal methods on page 32. 32. Be careful not to damage the black tab, located near the lid. If you need a top removal tool, please ple ase see www.easyinkjetrefill.com. www.easyinkjetrefill.com.
3.
Select Select the color to be refilled refilled and and fill fill a syringe syringe with with ink. ink. With the the cartridge cartridge upright, carefully insert the needle into the correct chamber, as indicated below, left, until the needle tip is halfway into the foam sponge.
4.
Slowly inject Slowly inject ink into the chamber of the chosen ink color. Injecting ink too quickly may trap air inside the cartridge. Amount of ink needed varies by cartridge and depends on how empty the cartridge is before refilling. As you add ink, watch the sponge surface closely. If ink appears around the needle or up the sides of the sponge, stop filling. Use the syringe to extract 0.5-1ml of ink to reduce overfilling. Refill each color by repeating t he above process, keeping the cartridge upright.
5.
Verify Verify ink ink flow by press pressing ing the the print head head against against a damp damp paper paper towel. towel. Each color should leave a solid line on the towel. If not all ink colors are visible, follow the priming instructions on page 30. 30.
6.
Once the cartridg cartridge e is refilled refilled,, tape the cartr cartridge idge top top securely securely in place.
7.
Re-install Re-install the the cartridge, cartridge, run run cleaning cleaning cycles, cycles, and print print test test pages. pages. If print print results are unsatisfactory unsatisfactory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” on page 28. 28. Do not attempt to t o print with this cartridge when it is empty as this could damage the print head. For best results, refill cartridges before they are empty. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Cyan
Yellow
Magenta
Standard Colors
www.easyinkjetrefill.com
Photo Cyan
Black
Photo Magenta
Photo 12A1990 (90), 1361760
Page 17
InkJet Refill Kit Recommended Tools
Drill refill hole using a 3mm bit within the marked section. Use a small rubber plug to seal the hole after filling.
Ink reservoir Sponge chamber
Canon: BC-30/BC-30e•BC-31/BC-31e•BC BC-30/BC-30e•BC-31/BC-31e•BC-33e•BCI-3Bk/BCI-33e•BCI-3Bk/BCI3eBk•BCI-3C/BCI-3eC•BCI-3M/BCI-3eM• 3eBk•BCI-3C/BCI-3eC •BCI-3M/BCI-3eM•BCI-3Y/BCI-3eY•B BCI-3Y/BCI-3eY•BCICI3PC/3PM•BCI-5Bk•BCI-5C/BCI-5M/BCI-5Y•BC 3PC/3PM•BCI-5Bk•BCI-5C/BCI-5M/BCI-5Y•BCI-6Bk•BCI-6C/BC I-6Bk•BCI-6C/BCII6M/BCI-6Y•BCI-6PC/BC 6M/BCI-6Y•BCI-6PC/BCI-6PM•BCI-8Bk•BCI-8C I-6PM•BCI-8Bk•BCI-8C/BCI-8M/BCI/BCI-8M/BCI8Y•BJI-201Bk(HC)•BJI-201C/BJI-201M/BJ 8Y•BJI-201Bk(HC)•BJI-201C/BJI-201M/BJI-201Y•CLI-8BK•CLII-201Y•CLI-8BK•CLI8C•CLI-8M•CLI-8Y•CLI-8PC•CLI-8PM•PGI-5 Apple: M1949•M1950•M1951•M1952•M3822•M3852
1.
Read pa pages 4-5 for important general information that will greatly improve your results.
2.
Press Press and and hold hold the ink ink outlet hole hole against against the rubbe rubberr sealing sealing pad, pad, maintainin maintaining g pressure pressure against the sealing pad to minimize leaking as you refill. If your kit does not include the rubber sealing pad, you may optionally use high quality black electrical tape. (If you do not seal the the ink outlet, ink will drip from the ink outlet hole until the refill hole is sealed with a plug.)
3.
Use the the included included 3mm drill drill bit to to drill a hole hole where where indica indicated ted at left. Be Be sure sure that the refill hole is clean and smooth, as the small plug must create an airtight seal once the cartridge is refilled.
4.
Inject Inject the appropr appropriate iate color color of ink ink into the the ink reserv reservoir oir until until it is full. Wait 151530 seconds for the ink to saturate the sponge. Add additional ink, if necessary, to fill the ink reservoir. reservoir.
5.
Seal the refill refill hole with with a small small plug. plug. If the seal seal is not not airtight, airtight, the cartri cartridge dge will leak. If you did not use the included 3mm drill bit, if the plug does not seal properly, or if the cartridge continues to leak, use hot glue to seal the refill hole. Do NOT use tape as it will not provide a proper permanent seal.
6.
After you remove remove the the tape or rubber rubber sealing sealing pad pad from the ink outlet, outlet, a few few drops of ink SHOULD SHOULD drip from from the cartridge. If you don't get any drips, hold the cartridge over paper towels and carefully remove the plug from the seal hole until the ink outlet begins to drip, then quickly repeat step 5.
7.
Let the the cartridge cartridge sit sit for 10-20 10-20 second seconds s until until it is no longer longer dripping dripping ink. ink. Give the sponge chamber a light squeeze for a final drip to balance the pressure. If the cartridge continually drips ink, refer to step 5 to seal the refill hole.
8.
Once the the cartridge cartridge is filled filled and and no longer longer dripping dripping ink, re-ins re-install tall the cartridg cartridge, e, run cleaning cycles, and print test pages. NEVER install a dripping or leaki ng cartridge in your printer.
9.
Some printers printers may may not be be able able to tell that that the CLI-8 CLI-8 and and PGI-5 PGI-5 type cartridges cartridges are full again after after reinstalling them in the printer. printer. If so, you may may need to either press press the button on the printer until the error light goes out, or use the printer driver option to continue printing. If you do this, be sure to keep the cartridges refilled BEFORE they run empty.
Ink outlet To prevent excess drips while filling, press and hold the ink outlet against the rubber sealing pad. As an alternate, use black electrical tape.
InkJet Cartridge Refilling Manual
For best results, do not leave empty or refilled cartridges out of the printer unless tightly sealed in a heavy plastic bag. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Page 18
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
InkJet Cartridge Refilling Manual
Canon: BC-20•BC-23•BX-20 BC-20•BC-23•BX-20 Apple Apple:: M3240 1.
Read pages 4-5 for important general information that will greatly improve your results.
2.
These These cartridg cartridges es have have a plug on the top of the the cartridg cartridge e that must must be removed removed as indicated at left. Press the included screw tool into the plug and turn clockwise until the tool is secured in the plug and you are able to pull the plug out. Keep the plug for reinserting reinserting into the cartridge fill hole.
Remove this plug from the fill hole using the screw tool
Although not required, required, we recommend using an accurate scale, such as a postal scale, to measure the cartridge mass. See pages 3434-35 for estimated cartridge mass/volume for various cartridges. 3.
Select the color to to be refilled refilled and and fill fill a syringe syringe with with ink. With With the cartr cartridge idge upright, carefully insert the needle into the refill hole until the needle tip is halfway into the foam sponge.
4.
Slowly inject Slowly inject ink. As you add ink, watch the print head closely. If ink begins to come out of the print head or around the refill hole, stop filling, then use the syringe to extract 1ml of ink.
5.
Reinse Reinsert rt the plug plug into into the the fill fill hole. hole.
6.
Verify Verify ink flow flow by pressi pressing ng the print print head head against against a damp damp paper towel. towel. The The print head should leave a solid black li ne on the towel. If ink is not visible, follow the priming instructions on page 30. 30.
7.
Re-install Re-install the the cartridg cartridge, e, run run cleaning cleaning cycles, cycles, and print print test test pages. pages. These cartridges cartridges are easy to overfill. Check / correct overfilling by following the instructions on page 33. 33.
Replace the plug after refilling. If the screw tool is still attached to the plug, rotate the screw tool counter-clockwise to remove it from the plug.
For best results, refill cartridges before before they are empty. Empty ink cartridges should be refilled promptly, as cartridges that are old or dry may not refill successfully. successfully. If necessary, refilled cartridges may be stored in a sealed plastic bag. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Press the print head against a paper towel to verify the ink flow.
www.easyinkjetrefill.com
Page 19
InkJet Refill Kit Recommended Tools
BCI-21,24 COLOR ONLY: Remove top of cartridge. See page 32.
Press small priming tip gently against ink outlet and slowly inject ink. Stop when ink comes out the bottom.
InkJet Cartridge Refilling Manual
Canon: BCI-10•BCI-11•BCI-15•BCI-21•BCI-24 Apple: M3329•M3330•M3908•M39 M3329•M3330•M3908•M3909•M3910•M3911•M3912 09•M3910•M3911•M3912 1.
Read pages 4-5 for important general information that will greatly improve your results.
2.
To reduce reduce the the risk risk of of ink contami contaminatio nation, n, we recomm recommend end remova removall of the cartridge top on color cartridges that have separate tops. Please review the cartridge top “Alternate Removal Methods” on page 32. 32.
3.
Place the the cartridge cartridge with with the ink ink outlet(s) outlet(s) facing facing up, as as shown shown below below at left, left, on a flat, ink-resistant surface or on paper towels or absorbent cloth in case of spills or leakage.
4.
Select color color to be refill refilled ed and fill a syring syringe e with ink, ink, then carefu carefully lly remove remove the needle and attach the small priming tip (page 3).
5.
Gently pres press s the priming priming tip agains againstt the ink ink outlet outlet on the cartridg cartridge e as slowly inject up to 5ml of color ink or up to 12ml of black indicated at left and slowly inject ink. It is important not to dent, mar, or damage the sponge when refilling or the cartridge will be unusable. Stop filling when the sponge is full and stops absorbing ink quickly. A dry sponge may absorb ink more slowly.
6.
Carefully Carefully turn turn the cartr cartridge idge to the the upright upright position, position, using using a paper paper towel or absorbent cloth to absorb any ink dripping from the ink outlet. Hold cartridge upright until ink no longer drips from the ink outlet. Installing the cartridge while ink is still dripping and/or running out of the cartridge may damage your printer.
7.
Tape the cartr cartridge idge top top securely securely in place, re-ins re-install tall the cartri cartridge, dge, run run cleaning cleaning cycles, and print test pages. Most Canon printers will automatically reset ink levels. For best results, refill your cartridge regularly. In some cases, the sponge may not absorb ink immediately. After refilling, allow 1-2 hours (12 hours for very dry sponges) for the sponge to absorb the ink. The BCI-21 cartridges contain more absorbent sponge material than the BCI24 and may provide better results, with longer time between refills. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Black Black
Inject carefully. Do NOT allow ink to enter any of the other colors. If you overflow, immediately wipe away any excess ink.
Color
Yellow Yellow Magenta Magenta Cyan Cyan Yellow Cyan Magenta
BCI-11
BCI-21/24
BCI-15
Color location varies. Check cartridge before refilling.
Page 20
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
InkJet Cartridge Refilling Manual
Canon: BC-01•BC-02•BX-2•BC-05•BC-06 Apple: M4609•M8041•M8049•M8052 Brother: IN10 Read pages 4-5 for important general information that will greatly improve your results. Black Cartridges: Cartridges: BC-01, BC-02, BX-2, M8041, M8049, M8052, IN10
Remove this plug from the fill hole using the screw tool
1.
These These cartridg cartridges es have have a plug on the side side of the the cartridg cartridge e that must must be remove removed d as indicated at left. Press the included screw tool into the plug and turn clockwise until the tool is secured in the plug and you are able to pull the plug out. Keep the plug for reinserting reinserting into the cartridge fill hole.
2.
Fill a syrin syringe ge with black black ink. ink. With the the cartridg cartridge e upright, upright, carefully carefully inse insert rt the needle into the refill hole until the needle tip is halfway into the foam sponge.
3.
Slowly inject Slowly inject up to 20ml of ink. As you add ink, watch the print head closely. If ink begins to come out of the print head or around the refill hole, stop filling, then use the syringe to extract 1ml of ink.
4.
Reinser Reinsertt the plug plug into the fill fill hole. hole. If the the plug is is badly badly damaged damaged you may may optionally insert a large rubber plug. Continue with the instructions and cautions under “Black and Color Cartridges” Cartridges” below.
Color Cartridges: BC-05, BC-06 and M4609 1.
The color color cartridg cartridge e has three three plugs plugs located located on the the side side of the cartridge cartridge (one (one for each color) as indicated at left. Each plug is removed by pressing the included screw tool into the plug and turning clockwise until the tool is secured in the plug and you are able to pull the plug out. Keep the plug for reinserting reinserting into the cartridge fill hole. Only remove one plug at a time when refilling to avoid color contamination.
2.
Yellow Magenta Cyan Set the cartridge on folded paper towels to drain any overfilled ink.
3.
Always check the the color color of the the ink in in the chamber chamber you are about about to fill. After After you have verified the ink color, slowly inject up to 5ml of the appropriate color of ink into the refill hole. The amount of ink remaining in each color may be different, depending depending on your printing. Refill until full, then remove 0.5 ml. Set the cartridge cartridge on on thickly thickly folded folded paper paper towels towels with with the vent vent holes holes facing facing down for about 5 minutes to drain any overfilled ink. Reinsert each plug into the fill hole and repeat procedure with any remaining colors.
Black and Color Cartridges Verify ink flow by pressing the print head against a damp paper towel. Each color should leave a solid line on the towel. If ink is not visible, follow the priming instructions on page 30. 30. These cartridges are are easy to overfill. Check / correct overfilling by following the instructions on page 33. 33. For best results, refill cartridges before before they are empty. Empty ink cartridges should be refilled promptly, as cartridges that are old or dry may not refill successfully. successfully. Store refilled cartridges in a tightly sealed plastic bag. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
www.easyinkjetrefill.com
Page 21
InkJet Refill Kit Recommended Tools
Brother: LC41BK/C/Y 1.
Use a syringe without a locking tip.
Ink Exit Hole
Pressure Release Button
InkJet Cartridge Refilling Manual
Read pa pages 4-5 for important general information that will greatly improve your results. results. Note: Refilling the LC41M LC41M is not recommended. recommended.
2.
Fill a syrin syringe ge without without a locking locking tip with 25ml 25ml of black black ink (for (for the LC41B LC41BK) K) or 20ml of color ink (for the LC41C or LC42Y). LC42Y). If your kit does not include a syringe without a locking tip (as shown at left), please visit www.easyinkjetrefill.com.. www.easyinkjetrefill.com
3.
Remove Remove the needle needle from from the the syr syring inge. e.
4.
Place the the cartridge cartridge on a flat, ink ink proof surf surface, ace, with with the bottom bottom facing facing up, as as shown.
5.
Push the tip of of the syringe syringe into into the ink ink exit hole hole and tilt tilt the syring syringe e to the side. side. Pull back on the syringe and tilt/rotate the syringe until air flows into the syringe easily.
6.
Pull the the syringe syringe back back until 3-4 3-4 ml of air air from from the cartri cartridge dge bubbles bubbles up through through the ink. A slight vacuum will form in the cartridge. Then, push on the syringe slightly to inject 3-4 ml of ink. Repeat this step 5-10 times to “pump” the air out of the cartridge and replace it with ink.
7.
When the refill refill proces process s is complete complete,, the syring syringe e will be be filled with air air but the plunger will be in the starting location. Pull back one last time on the plunger to pull a few extra ml of air out of the cartridge and then pull the syringe out of the ink exit hole Do not bump or press the pressure pressure release button during or after filling.
Fill to 25ml (black) or 20ml (color). You will need the remaining space in the syringe for air during the refill process.
8.
Re-install Re-install the the cartridge, cartridge, run run cleanin cleaning g cycles, cycles, and print print test test pages. pages. If print print results are unsatisfactory, unsatisfactory, be sure the cartridge is reinserted completely and correctly. These cartridges do not need to be refilled before they are empty. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
First, pull back on the syringe until 3-4 ml of air bubbles are pulled into the syringe. Then release (and gently push) an equal amount (3-4 ml) of ink into the cartridge.
Push the tip into the ink exit hole and tilt the syringe as shown.
Page 22
Pull back and push in repeatedly until all the ink is in the cartridge. Notice that the plunger of the syringe is in the starting position when finished.
Repeat until all the ink is in the cartridge.
Free Technical Support at 316.618.3500
InkJet Refill Kit Recommended Tools
InkJet Cartridge Refilling Manual
Epson: S020034•S020036•S020047•S020049•S020089•S020093 S020097•S020108•S020138•S02 S020097•S020108•S020138•S020187•S020189•S020191 0187•S020189•S020191 S020193•T001•T003•T005•T0 S020193•T001•T00 3•T005•T007*•T008* 07*•T008*•T009*•T013•T014 •T009*•T013•T014 • T015*•T016*•T017*•T018*•T019 T015*•T016*•T017*•T018*•T019•T020•T026*•T0 •T020•T026*•T027*•T028* 27*•T028* •T029*•T036*•T037*•T038*•T03 •T029*•T036*•T037*•T038*•T039*•T040*•T0 9*•T040*•T041* 41*
*Ink-level chip
Cartridges marked marked with a “*” have an ink-level chip that must be reset to use the cartridge after refilling. For instructions, see page 25. 25. Use a syringe without a locking tip.
1.
Read pages 4-5 for important general information that will greatly improve your results.
2.
Verify Verify the ink color color in each each chamber chamber before before filling filling (see (see “Use “Use Colors Colors Correctly Correctly” ” on page 5). Do NOT rely solely upon cartridge label or diagram colors. The diagrams below show the colors in the chamber as seen from the top.
3.
Fill ill a syri syrin nge without (without a locking tip if included) with ink. Remove air bubbles by pushing all the ink and air in the syringe back into the bottle and withdrawing ink again.
4.
Have paper paper towels towels ready ready to absor absorb b excess excess ink. ink. If usin using g a syringe syringe without without a locking tip, prepare for a few drips of ink, then remove the needle from the syringe and set the needle aside and put the tip of the syringe into the ink outlet for the color you are refilling, as shown. If using a syringe with locking tip, insert needle into the fill hole on the top of the cartridge (not shown). Slowly inject Slowly inject ink, gently tapping the cartridge after every few ml to help air bubbles escape. Injecting ink too quickly may stop you from filling the cartridge completely. As you add ink, watch the top vent holes closely. When ink begins to come out of the vent hole, stop filling but leave the syringe in place. Extract 1-2 ml of ink to remove air from the ink outlet and to reduce overfilling. Remove the syringe and clean away excess ink with paper towels.
5.
Wash and dry dry the needle needle and and syringe. syringe. Refill Refill each color color by by repeating repeating steps steps 2-4. 2-4. Place the filled cartridge on thickly folded paper towels and allow to sit for 2-3 minutes with the ink outlet down, then 2-3 minutes with the ink outlets up. Some ink may drip from the ink outlet and/or vent holes during this process.
6.
Follow Follow chip resettin resetting g instructio instructions, ns, if needed needed,, and re-inst re-install all the cartridge cartridge.. Run cleaning and test cycles. The best print quality is usually obtained after letting the printer sit idle with the refilled cartridges installed for 4-24 hours, then running cleaning cycles again.
Ink Outlets Stop filling when ink comes out the vent hole on the top.
If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com EPSON
Fill by injecting ink into the ink outlet. Air and bubbles may come out the top of the cartridge. When finished filling, withdraw 1-2 ml to remove air and reduce overfilling.
EPSON
Cyan Black
Yellow Magenta
All Black Cartridges
www.easyinkjetrefill.com
T005•T014 T018•T020 T029•T037 T039•T041 S020191 S020089
EPSON
Magenta
Yellow
Cyan S020036 S020049 • S020097
EPSON
Cyan Black
Yellow
Magenta
S020138
EPSON
Cyan
Magenta Yellow
Photo Photo Cyan Magenta S020193 • T001 T008 • T009 T016 • T027
Page 23
InkJet Refill Kit Recommended Tools
Ink Exit Hole
Then, release and gently push an equal amount of ink into the cartridge. Repeat as needed. Push the tip into the ink fill hole. Keep a tight seal.
Epson: T0431*•T0441*•T0442*•T0443*•T0444* T0481*•T0482*•T0483*•T0484 T0481*•T0482*•T0 483*•T0484*•T0485*•T04 *•T0485*•T0486* 86* T0601*•T0602*•T0603*•T0604*
Cartridges marked with a “*” have an ink-level chip that must be reset to use the cartridge after refilling. For instructions, see page 25. 25.
Ink Fill Hole
First, pull back firmly on the plunger of the syringe to pull air out of the cartridge.
1.
Read pa pages 4-5 for important information that will improve your results.
2.
Use a needle needle or screw screw tool tool to puncture puncture the the plastic plastic film over over the ink ink fill hole. hole.
3.
Fill the the large large syringe syringe with with exactly exactly 20ml of ink, remove remove the needle needle and attach attach a small priming tip. To make filling easier, we recommend trimming 3mm (1/8 inch) from the small end of the priming tip.
4.
Set the cartr cartridge idge upright, upright, as as shown, shown, and and push push the syrin syringe ge tip into into the ink fill fill hole until it makes a tight seal as shown. Maintain the seal while refilling.
5.
Carefull Carefully y note the starti starting ng position position of of the plunger plunger in in the syrin syringe. ge. Pull Pull firmly firmly on the syringe plunger to withdraw air from the cartridge, then allow t he plunger to go back to the starting position, filling the cartridge with ink. Repeat, pulling back quickly and firmly until you are unable to draw any additional air bubbles out of the cartridge.
6.
Carefull Carefully y remove remove the syring syringe e from the the fill hole, hole, tip tip the syringe syringe up, up, cover cover the priming tip with wadded paper towels and eject the air from the syringe.
7.
Repeat Repeat steps 4 and 5 until all all the air is is withdra withdrawn wn from from the cartrid cartridge. ge. If the the cartridge is empty, it will hold 15-16ml, leaving 4-5ml in the syringe. (The T0431extra large black holds 35-37ml, and will require a syringe refill.)
Hold the syringe down with a 8. finger.
9. Notice that the plunger of the syringe is in the starting position when finished.
Hold the cartridge steady. Use a clamp to help keep the cartridge upright, if available. Seal the fill hole with an extra large* rubber plug.
InkJet Cartridge Refilling Manual
Top off off the cartridg cartridge e by putting putting a needle needle on the the syringe syringe and and injecting injecting into into the fill hole until totally full. This cartridge cannot be overfilled. Wipe Wipe exces excess s ink from from the the fill fill hole hole and seal seal with with an an extra large* rubber plug. Extra large plugs are only included in kits that list these cartridges as compatible on the package. If you need extra large plugs, they are available for purchase at www.easyinkjetrefill.com. DO NOT use the regular large plug, silver tape dots, or tape. An improper seal may allow ink to leak after replacing the cartridge in the printer.
10. When completed, the cartridge should should weigh 40-43g 40-43g (~1.5oz). (~1.5oz). The T0431extra large black should weigh 67-69g (~2.5oz). Although not required, required, we recommend using an accurate scale, such as a postal scale, to weigh the cartridge after filling. If the cartridge is not at full weight, it is not full, and will run out before the printer expects it to. If you cannot get to the full weight, refill the cartridge again when your printer driver reports reports ink levels below 25% to prevent the cartridge from running completely dry. The printer should be able to print again immediately, or after 1-2 cleaning cycles. If not, place the cartridge with the ink exit hole facing down and withdraw a few ml of ink from the ink exit hole by inserting the tip of the large syringe and pulling back. Be sure to fill the cartridge again, or it will run out of ink before the printer expects it t o. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Page 24
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Epson: Ink-level Chip Reset Details and Instructions
Many Epson brand cartridges use ink-level chips that disable the cartridge when a pre-determined number of droplets are printed. To refill and use a cartridge with an ink-level chip, a chip reset device must be used. For more information, please visit www.easyinkjetrefill.com. www.easyinkjetrefill.com. Epson Chip Reset Device Instructions: 1. Chip Reset Device 2.
Epson Ink-level Chip
Standard Cartridges
Most cartrid cartridges ges can can be reset reset with with a standar standard d device device (shown) (shown).. Some large large format cartridges require a special large format reset device (not shown). If you have have a tall tall and thin thin cartridg cartridge e (see below below), ), prepare prepare the reset reset device device to fit fit your cartridge by installing a plastic guide.
3.
Align your your cartridge cartridge with with the chip chip reset reset device. device. The The pins on the reset reset device device must align exactly with the contacts on the ink-level chip on the cartridge.
4.
After a few seconds, seconds, the the LED light should should begin begin flashin flashing g red. If the the reset reset is successful, successful, the light l ight will turn green after 3-4 seconds. If the light does not flash, you have not made contact with the ink-level chip. Try pressing the reset device against the cartridge again, and with the cartridge and the reset device pressed together, move the reset device slightly back and forth, or up and down, to get a good contact with the chip. If the LED light turns solid red, it means that the reset could not complete successfully. successfully. This may be because the chip is damaged, it is not an original Epson chip, or is a chip that is not resettable.
Align the chip reset device with the cartridge
Never reset the ink-level chip without also refilling the cartridge completely. Doing this will tell the printer that the cartridge is full, and may cause the cartridge and printer to run completely out of ink, making it difficult to get the printer working correctly again.
Tall and Thin Cartridges Press the reset device against the cartridge so the pins on the reset device align with the metal contacts on the ink-level chip, and the light blinks red, then turns solid green.
www.easyinkjetrefill.com
Tall, thin cartridges are easier to reset if you use a cartridge guide. Tab
Position as shown, align the tab, and push the guide onto the reset device.
Press the reset device against the cartridge until the light blinks red then turns green.
Page 25
InkJet Refill Kit Recommended Tools
Brother: LC02BK/C/Y/M•LC04BK/C/Y/M•LC21BK/C/Y/M LC31BK/C/Y/M 1.
Release clip with screw driver Tape over the ink outlet on the cartridge bottom
Refill hole Vent holes
Carefully push ink into the sponge.
Stop here Then fill again
Page 26
Read pages 4-5 for important general information that will greatly improve your results.
2.
Tightly Tightly seal seal the ink outlet outlet on the bottom bottom of of the cartridg cartridge e with tape.
3.
Use a small small screw screw driver driver to pry the lid lid from from the cartri cartridge dge as indicated indicated at at left. The lid is easy to remove once you have released the clip.
4.
Study the the photos photos at left carefu carefully, lly, and note the the positions positions of the three holes holes under the stickers on the top of the cartridge. Remove the stickers to expose the refill and vent holes.
5.
Select the color to to be refilled refilled and and fill fill a syringe syringe with with ink. Insert Insert the the needle needle into into the refill hole and push the tip of the needle down through the fill chamber toward the bottom of the cartridge.
6.
Slowly inject Slowly inject ink into the cartridge until it rises up to the refill hole, and then carefully withdraw the needle from the cartridge.
7.
Attach the small small rubber rubber priming priming tip to an empty syring syringe e and slowly slowly force force air air into the fill hole (as shown in the image, below left) until most of t he ink in the chamber beneath the refill hole is pushed into the sponge. Stop when the ink nears the bottom of the chamber. Do NOT push all of the ink into the sponge, as air may become trapped in the cartridge.
8.
Repeat Repeat steps 5-7 5-7 until until the sponge sponge is satura saturated ted with with ink but befor before e the ink reaches the vent hole. The ventilation chamber (located below the vent holes) should remain empty. Be sure that the cartridge is filled with ink to the top of the refill hole.
9. This side must stay 10. empty 11. Fill until ink reaches the refill hole.
InkJet Cartridge Refilling Manual
Carefully Carefully wipe wipe the area area around around the refill refill and vent holes holes until until the cartrid cartridge ge is dry, then apply an included adhesive tape dot or use high-quality black electrical tape to form an airtight seal over each opening. Remove the tape covering covering the ink outlet outlet on the bottom of the cartridge. Ink may drip or seep seep from the ink outlet as the cartridge cartridge pressure pressure equalizes. equalizes. This may take some time if the cartridge is overfilled. If the outlet dripping drains all the fluid in the refill chamber, the refill and/or vent hole are not properly sealed and you should restart the procedure from the beginning, being sure to seal the refill and vent holes fully.
12. When you have verified verified that the refill and vent holes are sealed properly, reinstall the cartridge, run cleaning cycles, and print test pages. If your printer indicates that the cartridge is empty after refilling, check to ensure that the ink level in the refill chamber reaches the refill hole. 13. If you have followed the instructions instructions carefully carefully but need additional help, please review pages 34-35. If your printer indicates that the cartridge is still empty after refilling, make sure the ink fills the left chamber up to the refill hole. If you followed the instructions carefully but need additional help, please visit www.easyinkjetrefill.com
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
More instructions are available at www.easyinkjetrefill.com at www.easyinkjetrefill.com Refilling instructions and/or additional information and requirements for the following cartridges are available at www.easyinkjetrefill.com: Hewlett Packard: C4836 (11)**•C4837 (11)**•C4838 (11)** C4841 (10)**•C4842 (10)**•C4843 (10)**•C4844 (10)** C9359 (59)•C9368 (100)
Canon: BC-60•BCI-61•BCI-61e• BCI-62•BCI-62e•BCI-6R•BCI-6G CL-40•CL-41•PG-40•PG-41
Epson: S020062 (K)•S020118 (K)•S020122 (Y)•S02 ( Y)•S020126 0126 (M)•S020130 (M)•S020130 (C) S020143 (M)•S020147 (C) T480 (T480011)•T481 (T481011)•T482 (T482011)•T483 (T483011) T484 (T484011)•T485 (T485011)
Other/New: Additional or updated instructions, troubleshooting guides, and manuals are available on our website.
* Ink is compatible with these cartridges, but they may may require an ink-level chip reset to print. See the instructions for the cartridge, or page 25 for details. ** These cartridges may require require a third party replacement chip and resetter. See page 31 for details.
www.easyinkjetrefill.com
Page 27
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Tri-color Cartridge Troubleshooting: Unsatisfactory Unsatisfactory print results or incorrect colors with color HP, Lexmark, Compaq, Dell, or other similar multi-color cartridges: 1.
Ink contamin contamination ation will will cause cause the the printer printer to to produce produce off-color off-color output. output.
2.
Contaminati Contamination on usually usually occur occurs s when when one one or more colors colors have have been overfilled and can occur even if overfilling was not obvious. The overfilled color forms a small ink drop on the print head. The sponges containing the other colors wick the overfilled color up into their chambers. This causes causes the overfilled color to combine with and contaminate other colors.
3.
In some some cases, cases, contamin contamination ation can can be caused caused by failure failure to suffi sufficient ciently ly wash the needle and syringe or by accidentally injecting the wrong color. The procedure below may not resolve color contamination due to these errors. If this is the cause of your color contamination, please follow the cartridge priming procedures on pages 29 and/or 30 to purge your cartridge, then refill the cartridge again, using the appropriate instructions. Repeat as needed.
4.
To resolve resolve ink contamina contamination tion cause caused d by overfil overfilling, ling, download download the the color color test page from www.easyinkjetrefill.com. This test page uses the color management capabilities of a free software package called OpenOffice.org. OpenOffice.org. OpenOffice.org is compatible with virtually all modern operating systems.
Figure 1: Example test page created in OpenOffice.org's OpenOffice.org's Draw program. You will find a link to download this test document on our web site: www.easyinkjetrefill.com
Alternately, if you already have a drawing or graphics program on your system, make your own test page using black, cyan, 5. magenta, and yellow bars.
Print Print the test test image repea repeatedly tedly until until the colors colors print print properly. properly. The The number number of prints required depends upon the degree of contamination. If you have trouble only with a specific color, you may wish to expand the bar for that color and/or remove the bars of color that are working correctly to save ink. The OpenOffice.org OpenOffice.org Draw application is used for this color page because it is easy to use and allows “pure” colors to be printed. You can create a similar test page in any available drawing or graphics program, program, but your color purity may vary.
HP Printer Maintenance Codes
Page 28
Make/Model Series
Task Performed
Sequence Code
Sequence Description (Hold down the Power button and..)
HP / 9XX / 8XX
Light Clean
20 Tap
Tap Cancel twice
HP / 9XX 9XX / 8XX 8XX
Inte Interrmedi ediate
21 Tap
Tap Cancel twic wice, then Res Resume onc once
HP / 9XX / 8XX
Prime
22 Tap
Tap Cancel twice, then Resume twice
HP / 9XX
Self Test
84 Tap
Tap Cancel 8 times, then Resume 4 times
HP / 9XX / 8XX
Status Page
41 Tap
Tap Cancel 4 ti times, then Resume once
HP / 8XX
Self Test
4 Tap
Tap Resume 4 times
HP / 6XX / e20
Pen Clean
7 Tap
Tap Resume 7 times
Free Technical Support at 316.618.3500
InkJet Refill Kit HP Cartridge Clip Tool
InkJet Cartridge Refilling Manual
Preparing to Use the Clip Tool 6.
Place the the ink cartrid cartridge ge in the the cartridge cartridge refill refill clip clip by placing placing the print print head head against the flat surface of the rubber tip and squeezing the cartridge into the clip with gentle pressure toward toward the center of the cartridge until it snaps into place. Do not force the top of the cartridge down once it is clipped. There should be a small gap visible.
7.
Ensure Ensure that that the print print head head is aligned aligned with with the refill refill hole hole in the the rubber rubber tip tip and that it fits flush against the base of the clip. If necessary, adjust the cartridge position by removing and reinserting the cartridge.
Syringe styles may vary. Always use a syringe with a locking tip, as shown, Leave a when using the cartridge refill clip. gap as shown to help Refilling with the Clip Tool ensure the head is CAREFULLY CAREFULLY follow the instructions below. It is important to hold both the properly syringe and the cartridge securely while refilling. DO NOT attempt to inject aligned ink too quickly. Excess pressure pressure may break the seal or cause the syringe to separate from the rubber tip, resulting in dripping or spraying ink! Note: syringe tip styles may vary. Always use a syringe with a locking tip.
Ensure that the seal is tight
1.
Attach a needle needle to a clean clean syringe, syringe, fill the the syring syringe e with ink ink and and then carefully remove the needle. Attach the locking tip of the syringe to the rubber tip on the refill clip, and SLOWLY inject ink into the cartridge through the print head.
2.
As you you inject inject ink, make certain certain that the syringe syringe and and cartrid cartridge ge remain remain securely attached. Refill the syringe as needed. Inject ink until the cartridge is full, usually 25 to 40ml.
3.
Balance Balance the press pressure ure in the cartrid cartridge ge by rotating rotating the the cartridge cartridge clip clip until until the print head and syringe are upright and slowly withdrawing the plunger until air and approximately 3ml of liquid ink is drawn into the syringe.
4.
Remove Remove the cartri cartridge dge from from the the refill refill clip and and clean clean the print print head with a damp paper towel. Hold the cartridge upright for 30 seconds and watch the printhead for seeping or dripping ink.
Inject ink slowly!!
HP Cartridge Priming Cartridges that have run completely dry may not print properly when refilled. Priming the cartridge using the instructions below may correct this problem. For best results, always refill cartridges before they are empty.
Warning: Never push ink back into a multicolor cartridge.
1.
Attach the the locking locking tip of a clean clean syringe syringe to to the rubbe rubberr tip on on the refill refill clip.
2.
Once you are are sure sure that the seal seal is tight, positi position on the cartrid cartridge ge as shown shown,, and pull back on the plunger until ink begins to flow into the syringe. Never push ink back into a multi-color cartridge.
3.
Remove Remove the cartridge cartridge from from the refill refill clip and and clean clean the print head and contacts with a damp paper towel.
4.
Re-install Re-install the the cartridge cartridge,, run cleani cleaning ng cycles, cycles, and print print test test pages. If If print print results are unsatisf unsatisfactory actory or colors are incorrect, please refer to “Tri-Color Cartridge Troubleshooting” Troubleshooting” on page 28. 28.
5.
If prints prints are are still streaky streaky,, use the large large and/or and/or small small priming priming tip as descr described ibed on page 30. 30.
www.easyinkjetrefill.com
Page 29
InkJet Refill Kit
InkJet Cartridge Refilling Manual
General Cartridge Priming 1. 2. Small and large priming tips. These can be trimmed to fit your cartridge.
Use the small priming tip for small print heads or specific colors or nozzles. Seal must be air tight. tight. Trim tip if necessary.
Page 30
The large large priming priming tip tip is for for priming priming an entir entire e print head. head. To To use it, you must must press the large end to the outlets on your print head, forming an airtight seal. Pull back on the syringe to apply suction to the print head until ink or ink bubbles appear in the syringe. If you cannot establish an airtight seal, you may need to trim the priming tip to better fit the size of your print head. Be sure to trim the tip evenly, or the tip may not seal properly.
3.
If you are are priming priming a color color cartridge cartridge,, visually visually inspect inspect the color color of the ink in the syringe. This may indicate which colors are flowing through the print head properly. When primed properly, ink will flow into the syringe easily. If you cannot get any ink to pull into the syringe, the cartridge may be dried out. Try soaking the print head in warm distilled water for several hours, then prime again.
4.
Wipe the the print print head with with a damp damp paper towel and examine examine the nozzles nozzles (the (the tiny holes on the print head). Press Press the print head to a damp paper towel, and then to a dry one and examine the uniformity. The printhead should be clean and the nozzles should uniformly uniformly release ink.
5.
The small small suction suction tip is for for priming priming individu individual al nozzles nozzles.. It is used used in much much the same way as the larger tip, but it is designed to target specific nozzles that need to be primed.
6.
Press Press the tip tip lightly lightly over the clogged clogged nozzles nozzles and and draw draw the syring syringe. e. You should feel some resistance resistance or see ink flow if you are making a good seal with the surface. If you see the wrong color of ink, t hen you may be missing the targeted nozzle. Adjust the position of the syringe and try again. You may trim the small priming tip if you need to cover a larger area. Be sure to trim the tip evenly, or the tip may not seal well.
7.
After you you have have finish finished, ed, clean clean the the head head and contacts contacts with a damp paper paper towel. Place the cartridge into your y our printer and run test/cleaning cycles as described in your printer manual.
Pull back on the syringe to prime the cartridge.
Seal must be airtight. Trim if necessary.
Priming Priming tools tools are provid provided ed in the the refill refill kit. Begin Begin by attaching attaching a small small or large priming tip to a clean, dry syringe.
The small priming tip may also be used in conjunction with a rubber square square to remove air from a cartridge so more ink can be injected. Use a large syringe about half full of ink to start. Temporarily seal any extra holes in the color chamber you want to fill with rubber plugs or tape. Start by pulling back on the t he syringe to extract air from the cartridge. Then, when you gently push back down on the syringe, ink will enter the cartridge. Repeat this cycle 5-10 times until no more air can be extracted from the cartridge. When completed, prime the cartridge again with the priming tip as described above.
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Resetting Ink levels Many printers or print drivers use droplet droplet or page counters to track ink usage. In most cases it is NOT necessary to reset the page/droplet counter. In some cases, however, this can be a useful tool for determining when a cartridge should be refilled. Printing Printing with an empty cartridge can damage a print head, so low ink warnings can help prolong printhead life if the cartridge is promptly refilled. If you cannot or do not reset the ink-counter, be sure to refill frequently to ensure your cartridge does not run dry. Reset procedures can differ for each printer model and/or printer driver, so always check documentation and manuals provided with your printer or printer driver before attempting any reset method. Some manufacturers may include instructions on how to reset or override these counters from the printer or within the driver software. Listed below are various methods that may be used by the manufacturer to track ink usage.
Self-Resetting Printers: Some printers use a combination of counters and sensors. sensors. When properly filled and returned to the printer, these cartridges will read as full. Some Canon and Brother printers behave this way.
Menu/LCD Reset: Some multifunction printers will ask if the printer cartridge is new every time i t is replaced in the printer carriage. When you choose “new,” the printer will reset the droplet counters and treat this cartridge as new. Some do not detect when the cartridge has been replaced, but have a menu option for replacing the cartridge. Always read the your printer manual before removing the cartridge to determine the proper method.
Driver Reset: The drivers that came with your printer may have a tool under the maintenance tab (if using Windows) for setting your cartridges as new. Your printer or driver manual will have information in the section for changing printer cartridges.
Cartridge Memory: Some printers (including many HP models) have a “memory” that recalls the last few cartridges of each model used in the printer. Procedures Procedures exist for some of these printers that attempt t o rotate the current cartridge ID out of the printer memory. Sometimes old cartridges can be used in this rotation procedure once they have exceeded their useful life cycle. Many such printers allow you to continue printing with a used cartridge until the cartridge fails despite annoying warning messages. These These counters are more like an odometer than a gas gauge and may not reset until you replace the cartridge. Printing with an empty cartridge can damage a cartridge's print head, so be careful to refill before the cartridge is empty in order to prolong the life of your cartridge.
Chip Reset: A few HP cartridges (such as the HP 10/11) 10/11) will have a separate print head and require a replacement chip and resetter specific to the cartridge. You may wish to perform an Internet search for your cartridge model(s) and color(s) to find the specific chip and resetter required for your cartridge.
Alternate Instructions: Many unverified instructions for resetting or overriding cartridges cartridges may be available online as new cartridges and procedures are developed. Stratitec, Inc. does not support or guarantee such procedures. For further information information on this subject, please contact our Customer Solution Center.
www.easyinkjetrefill.com
Page 31
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Cartridge Top Removal Be careful not to damage the metal contacts located on the back of your cartridge when using any tools to remove the cartridge top.
Cartridge opening tool, included with some kits.
Push-bar Plastic Spacer for use with HP cartridges
Turn handle clockwise to apply pressure
1.
Some kits kits may may include include a cartrid cartridge ge opening opening tool. tool. The cartridge cartridge openin opening g tool is designed for specific HP and Lexmark color cartridges. If you need a top removal tool, please see www.easyinkjetrefill.com. www.easyinkjetrefill.com.
2.
Prepare Prepare the the tool by turni turning ng the handle handle counter-c counter-clockwis lockwise e to ensure ensure that that the push-bar is out of the way.
3.
If removin removing g the top from from an HP HP cartridg cartridge, e, fit the the plastic plastic spacer spacer into the the tool (see photo at left).
4.
Insert Insert the cartrid cartridge ge into the the tool so that that the push-b push-bar ar aligns aligns with with the top of the cartridge, as shown in the photos. The edges of the cartridge top should slide snugly into the grooves in the tool.
5.
Turn the handle handle of the the tool clockwis clockwise e to apply press pressure ure to to the cartridg cartridge e top. Continue turning the handle firmly until the top cracks or pops loose. Turn the handle counter-clockwise to loosen the push-bar and remove the cartridge.
6.
Use a flat screw screwdrive driverr or pliers pliers if if necessa necessary ry to completely completely remove remove the the top from the cartridge. Use tools with care to avoid damaging the sensors on on the back of the cartridge.
Alternate Removal Methods (see photos, below) If your kit does not include a cartridge opening tool, or if the cartridge opening tool does not work for your cartridge, you may try to carefully remove the top of the cartridge using channel-lock pliers or a small screwdriver. screwdriver. Use care to prevent damage to the metal contacts located on the back of the cartridge. If the top is difficult to remove, use the included 3mm drill bit to make a hole above each ink chamber instead of removing the top. Refer to the color location diagrams included with the specific instructions for your cartridge, and drill straight down to the sponge for each color chamber. Be very careful to avoid Carefully overfilling, as ink can overflow into other color chambers under the lid. score the corners and then along the seam of the cartridge.
It may be helpful to carefully score the seam of the cartridge top. WARNING: Use extreme caution if you choose to use a knife to score the seam of the cartridge. Keep the refill kit and tools, such as knives, out of reach of children.
Alternate Methods
Page 32
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Check / Correct Overfill It's easy to overfill some cartridges, especially multi-chambered color cartridges with opaque plastic. Many popular cartridges, such as the HP 17/23/25/78 17/23/25/78 and 28/57/58/95/97/99/100 28/57/58/95/97/99/100 types, Lexmark 20/65/80/90 20/65/80/90 and 26/83/31/33/35 26/83/31/33/35 types, Canon BCI-21/24 and most older Epson types are constructed in this manner. In multi-chambered cartridges, colors are used at different rates, and there is no way to tell how much ink remains in any given chamber. This makes it easy to overfill at least one color. It is very important to carefully check for and correct any possible overfill condition.
Epson and Canon:
Use paper towels to absorb excess ink from Canon and Epson cartridges
1.
Epson Epson and most most Canon Canon color color cartridg cartridges es do not not have built-in built-in print print heads. heads. (For older Canon cartridges with built-in heads, please follow the HP and Lexmark instructions below.)
2.
After filling, filling, let the the cartridg cartridge e sit upright upright on a thickly thickly folded folded stack stack of paper paper towels for 5 minutes. This allows ink to soak into the internal sponge and excess ink to drain from the bottom of the cartridge.
3.
Flip the cartrid cartridge ge upside-do upside-down wn and and place it on a thickly-folded thickly-folded stack of of paper towels for 5-10 minutes to allow any excess ink to drain into the towels.
4.
Repeat Repeat with fresh fresh paper paper towels towels until until no more more ink drain drains s from from the cartridg cartridge. e.
HP, Lexmark, Compaq, Dell, etc.: 1.
These These cartridg cartridges es contain contain a built-in built-in print print head. head. After After filling filling the cartrid cartridge, ge, wipe the print head with a damp paper towel. Ink from each color in the cartridge should soak into the paper towel. If all the ink colors do not appear on the paper towel, the print head may be clogged, making it hard to detect an overfill condition for the clogged color. When the clog clears, excess ink may flow out quickly and contaminate other colors.
2.
Use the cartrid cartridge ge refill refill clip for for large large HP HP cartridg cartridges es (see (see page page 29) 29) and the large priming tip for all others. Once you are sure that the seal is tight, draw from the cartridge until ink begins to flow into the syringe. Never push ink back into a color cartridge.
3.
After you have have finish finished, ed, wipe the print print head head and contacts contacts with with a damp damp paper towel.
4.
Place Place the cartri cartridge dge into into your printer printer and and run run test/clea test/cleaning ning cycles cycles as as described in your printer manual.
Use the refill clip to pull excess ink from large HP cartridges
Use the large priming tip to remove excess ink from HP, Lexmark, Compaq, Dell or similar cartridges
www.easyinkjetrefill.com
Page 33
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Cartridge Estimated Mass / Volume Many cartridges have an optimum mass (weight) when properly filled. Filling cartridges to their optimum mass helps ensure consistent and highquality results. Use a small lab or postal scale, to measure your cartridge mass. Use the tables listed here to determine the recommended mass of your refilled cartridge and fill to that level. Follow these tips for weighing a cartridge to determine its mass: •
Remove any tape, packaging or storage clips before measuring the cartridge mass/volume.
•
Keep the scale on an even, solid surface to generate the most accurate measurements. measurements.
•
Be sure to zero your scale before you place the cartridge for measurement. measurement.
•
Check that cartridge is not dripping or leaking ink before placing it on a scale. If you get ink on your scale, wipe it off immediately with a damp paper towel. You may need to zero your scale again.
Hewlett-Packard M od el 51 626 51 629 51 633 51 645a 51 640a 51 640c 51 640m 51 640y 51 644c 51 644m 51 644y C661 4a C661 5a C6656a C87 27 a C9368
Alias 26 29 33 45 40 40 40 40 44 44 44 20 15 56 27 1 00
Lexmark Mode Modell 1 380620 10N0 10N00 016 12A 12A1970 1970 13400HC 13620HC 17G0 17G0050 18L0 18L00 032
Alias
Full Full Mass Mass 65g (2.28oz ) 16 36g (1.2 1.26oz) 70 65g (2.28oz) 400HC 400HC 65g (2.28oz (2.28oz)) 620HC 620HC 65g (2.28oz (2.28oz)) 50 50 65g (2. (2.28oz) 82 42.3g (1.4 1.49oz)
F u ll Mass 60g (2.1 1 oz ) 60g (2.1 1 oz ) 60g (2.1 1 oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 1 10g (3.86oz ) 49g (1 .7 2oz ) 1 10g (3.86oz ) 47 g (1 .65oz ) 43g (1 .51 oz ) 44.8g (1 .57 oz )
Canon M od e l BC- 01 BC- 02 BC-20 -20 BC-23 -23 BCI-10 I-10 BCI-11 CI-11 BCI-15 CI-15 BCI-2 CI-21
F ul ull M ass 60g (2.1 1o 1oz ) 60g (2.1 1o 1oz ) 85g (2.99oz) 85g (2.99oz) 13g 13g (0.46oz) 5.5g (0.19oz) 19oz) 9.2g (0.32oz) 23.8g (0.84oz)
You may wish to estimate the amount of ink required to refill your cartridge by subtracting the mass of the empty cartridge from the estimated full mass. Use this value when filling the syringe with ink. The difference in grams will be approximately equal to (≈) the difference in milliliters of ink.
For additional help and resources, please visit www.easyinkjetrefill.com
Page 34
Free Technical Support at 316.618.3500
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Cartridge Estimated Mass / Volume Epson Mode Modell S0201 1 8 S020189 189 T0262 026201 01 T0282 028201 01 T04012 040120 0 T043120 043120 T044120 044120 T0442 044220 20 T0443 044320 20 T0444 044420 20 T048120 048120 T0482 048220 20 T0483 048320 20 T0484 048420 20 T0485 048520 20 T0486 048620 20
Alias
T026 026 T028 028 T040 T0431 0431 T0441 0441 T0442 0442 T0443 0443 T0444 0444 T0481 0481 T0482 0482 T0483 0483 T0484 0484 T0485 0485 T0486 0486
Brother
Full Full Mas Mass 1 83g (6.43oz ) 42.5g (1.4 1.49oz) 32. 32.3g (1.14oz) (1.14oz) 35. 35.7g (1.25 (1.25oz) oz) 34.7g 4.7g (1.22 (1.22oz) oz) 67.1g 67.1g (2.36 (2.36oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz)) 40. 40.5g (1.42 (1.42oz oz))
Model del Ful Full Mass LC41CMY LC41CMY 34g 34g (1.19oz) LC4 LC41BK 1BK 46g (1.6 (1.62oz)
Troubleshooting Table Problem
Cause
Solution(s)
Cracked cked or wr wrinkle nkled dp prrints ints
Pape Paperr qu quality lity low low or or pap paper er setti ettin ng Use high-quality paper incorrect Try another paper brand/type
Prints Prints have have scatter scattered ed droplet droplets s
Slight Slightly-ov ly-over erfil filled led cartri cartridg dge: e: ink droplets not forming properly
Print solid pages of black and/or color to clear overfill condition
Black and white photos have color tint
Color balance not perfectly matched
Use software to add counter-tint before printing
Drips of ink on paper when printing
Overfilled cartridge: ink pooling on print head
Use syringe to remove excess ink
Streaky prints
Clogged nozzles
Ink stains
Spilled ink
Prime the cartridge or print head Allow printer to sit overnight Wash with soap and water. Fades from skin in a few days.
For additional help and resources, please visit www.easyinkjetrefill.com
www.easyinkjetrefill.com
Page 35
InkJet Refill Kit
InkJet Cartridge Refilling Manual
Limited Product Warranty STRATITEC warrants to the original purchaser of this inkjet refill kit that this kit shall be free of defects in assembly, or workmanship, and will repair, or replace, at its option, any defective product free of charge (the "Limited Product Warranty"), subject to the conditions, limitations and exclusions set forth herein. Conditions and limitations applicable to the Limited Product Warranty are as follows. All costs of shipping the STRATITEC inkjet refill kit and any equipment to and from STRATITEC shall be borne solely by the purchaser. STRATITEC'S LIABILITY IS LIMITED TO REPLACEMENT OR REIMBURSEMENT OF THIS STRATITEC PRODUCT. Disclaimer of other Warranties and Limitation of Remedies. The Limited Product Warranty is the only warranty made by STRATITEC. EXCEPT AS SPECIFICALLY REQUIRED BY APPLICABLE LAW, THERE ARE NO N O OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, and such implied warranties, if any, are limited in duration to twenty-four (24) months from the date of original purchase. IN NO EVENT SHALL STRATITEC BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS , BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF SALE OR USE OF ANY STRATITEC INKJET REFILL KIT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Sales within the United States and Canada. The limited Product Warranty is made only to original purchasers who accept delivery of the Stratitec Inkjet Refill Kit within the United States or Canada. SOME STATES IN THE UNITED STATES AND SOME JURISDICTIONS IN CANADA DO NOT N OT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, THE EXCLUSION OF IMPLIED WARRANTIES AND/OR THE LIMITATION OF REMEDIES, INCLUDING EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES, IN CONSUMER TRANSACTIONS, IN WHICH CASE THE DISCLAIMER OF OTHER WARRANTIES AND LIMITATION OF REMEDIES STATED IN THE PRECEDING PARAGRAPH DO NOT APPLY TO YOU. For example, if you are an individual and purchased this STRATITEC Inkjet Refill Kit in the State of Kansas, you have rights based on implied warranties and none of the limitations and disclaimers set forth in the preceding paragraph apply to you.
Stratitec, Inc. Wichita, KS 316.618.3500
Page 36
Free Technical Support at 316.618.3500
