Transcript
Necsel Neon Specification Page 1 of 3 1 Introduction These specifications are for the Necsel Neon prototype laser illumination systemcontaining red, green and blue colors which can be independently modulated. The light isdelivered via a standard SMA-905 optical fiber output with a 1.0 mm aperture. 2 Operating Specifications and Characteristics Item Parameter SymbolLimitsMin Typ MaxUnit 1Operating Power (all colorsmaximum power) 3,6 P op 9.1 - 10.0 W2 Output Power Stability 1 - - 3 5 %PP3 Operating Temperature Range T 15 - 30 C4 SMA-905 Output Fiber Diameter Ø 1.0 - 1.0 mm5 Output Fiber Numerical Aperture NA 0.30 0.39 0.40 -6 Infra-Red Leakage 2 P IR - 20 40 mW7 Weight -- 17 - lbs- 7.7 - kg8 Red Wavelength Specifications 8.1 Center m 636 638 642 nm8.2 Spectral Width m - 3 5 nm8.3 Operating Power Range 3 P op 0.0 - 5.0 W8.4 Maximum Power 6 P max 4.5 - 5.0 W9 Green Wavelength Specifications 9.1 Center m 528 532 536 nm9.2 Spectral Width m - 0.2 0.5 nm9.3 Operating Power Range 3 P op 0 - 2.5 W9.4 Maximum Power 6 P max 2.3 - 2.5 W10 Blue Wavelength Specifications 10.1 Center m 462 465 469 nm10.2 Spectral Width m - 0.2 0.5 nm10.3 Operating Power Range 3 P op 0 - 2.5 W10.4 Maximum Power 6 P max 2.3 - 2.5 W Necsel ™ Neon RGB Laser Illuminator Specifications Date: December 10, 2011 Version: 3.1 Necsel Neon Specification Page 2 of 3 Item Parameter SymbolLimitsMin Typ MaxUnit 11 Warm-Up Times 11.1 Warm-up time (cold) 4 T on - 0.3 5.0 min12 AC Power Source Requirements 12.1 Input Voltage V input 100 - 240 V12.2 Input Current I input - - 3.5 A12.3 Input Frequency 50 - 60 Hz12.4 Total Power Consumption 5 P Total - 280 - W 1 Over 2 hours, after warm-up and ±3ºC, above 2W output power for each operating color 2 IR leakage at max power for all colors 3 Power is measured coming out from the SMA connector of the box. Power will be less after transport fiber is connected depending onAR-coating, fiber diameter, fiber length, and other factors. 4 ON is 90% of Item 1 P op 5 Power consumption measured at operating power of Item 1 at 25 ºC. Consumption will be much lower if lasers are run at lower powerlevels, and also will be affected by the environment temperature as TECs are used to heat/cool the lasers. 6 Maximum operating power will be lower than the indicated maximum when the white light homogenizing option is installed (i.e., thefiber output is white light instead of the individual RGB combination) 3 Communications Interface DMX 3-channel interface via 5-pin XLR connector USB Simple GUI with basic power commands for smooth RGB control Key-enabled turn-on for safety Extensive user command set provided upon purchase of Necsel Neon system 4 Mechanical Specifications 4.1 Necsel Neon Photographs Necsel Neon Specification Page 3 of 3 4.2 Mechanical Interfaces 4.2.1 Fiber Connection Necsel recommends at least a 1.0 mm diameter fiber at the output of the box inorder to capture the maximum amount of exiting light. The fiber tips should also beanti-reflection (AR) coated for maximum efficiency. 4.2.2 Mechanical Dimensions All dimensions below are in inches.
