Transcript
21FL91
SERVICE MANUAL SX2U321FL91//
COLOR TELEVISION
Chassis No. GA-2
MODEL
21FL91
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS Page » ELECTRICAL SPECIFICATIONS ......................................................................................................... 1 » IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2 » LOCATION OF USER'S CONTROL ..................................................................................................... 4 » INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5 » SERVICE MODE .................................................................................................................................. 6 » ADJUSTMENT METHOD ................................................................................................................... 11 » CHASSIS LAYOUT ............................................................................................................................. 26 » BLOCK DIAGRAM .............................................................................................................................. 27 » SCHEMATIC DIAGRAMS ................................................................................................................... 33 » PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 38 » REPLACEMENT PARTS LIST ............................................................................................................ 42 » PACKING OF THE SET ...................................................................................................................... 48
ELECTRICAL SPECIFICATIONS POWER INPUT ....................................... AC 110~220 V, 50/60 Hz POWER RATING .................................................................... 95W PICTURE SIZE .......................................... 1,239 cm2 (192sq inch) CONVERGENCE ............................................................. Magnetic SWEEP DEFLECTION .................................................... Magnetic FOCUS ............................................... Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ..................................... 45.75 MHz Sound IF Carrier Frequency ...................................... 41.25 MHz Color Sub-Carrier Frequency .................................... 42.17 MHz (Nominal) AUDIO POWER OUTPUT RATING ........................................ 3.0 W(RMS) x 2pcs
SHARP CORPORATION
SPEAKER SIZE ................................................................... 12 x 5 cm, 2pcs VOICE COIL IMPEDANCE ............................. 16 ohm at 400 Hz ANTENNA INPUT IMPEDANCE VHF/UHF ..................................................... 75 ohm Unbalanced TUNING RANGES VHF-Channels ............................................................... 2 thru 13 UHF-Channels ............................................................ 14 thru 69 CATV Channels ........................................................... 1 thru 125 (EIA, Channel Plan U.S.A.)
Specifications are subject to change without prior notice.
This document has been published to be used for after sales service only. The contents are subject to change without notice.
21FL91
IMPORTANT SERVICE SAFETY PRECAUTION Ë
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value −no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.) 1. Picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
2
21FL91
IMPORTANT SERVICE SAFETY PRECAUTION (Continued) • Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. • Plug the AC cord directly into a 110~220 volt AC outlet, (Do not use an isolation transformer for this test). • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.
1.5k ohm 10W
0.15 F TEST PROBE
TO EXPOSED METAL PARTS
CONNECT TO KNOWN EARTH GROUND
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SAFETY NOTICE Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
21FL91
LOCATION OF USER'S CONTROL
4
21FL91
INSTALLATION AND SERVICE INSTRUCTIONS Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic screwdrivers or TV alignment tools. (2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 3.15A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST 1. Connect an accurate high voltage meter between ground and anode of picture tube. 2. Operate receiver for at least 15 minutes at 110~220V AC line voltage, with a strong air signal or a properly tuned in test signal. 3. Enter the service mode and set Y-mute ON by using Service R/C. 4. The voltage should be approximately 28.7kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.
After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows: 1. Apply 110~220V AC using a variac transformer for accurate input voltage. 2. Allow for warm up and adjust all customer controls for normal picture and sound. 3. Receive a good local channel. 4. Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 18.9 ±1.1V. 5. Apply external 24.5V DC at TP653 by using an external DC supply, TV must be shut off. 6. To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen. 7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.
5
21FL91
SERVICE MODE Service Mode Overview 1. 2. 3. 4. 5.
Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset. Service mode is cleared by entering SERVICE key command during service mode. If key input port (SERVICE) input is LOW, then it is in service mode. During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE is disabled. Service mode can be switched to 4 modes as follows by key input MENU;
Adjustment mode
First mode of service mode when SERVICE key is pressed.
Setting mode
Check mode
First mode of service mode when local key CH-UP + VOL-DOWN is pressed after MCU reset.
Option mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data. 7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively in service mode. Energy Save is off. 8. Sleep timer, View timer and Off timer are inactivated in Service mode. 9. Sound is muting in service mode except at Adjustment Items V20, M01, M03, M04, M05, and M06.
6
21FL91
Adjustment Mode Items No. V01 V02 V03 V04 V05 V06 V07 V08 V09 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 M01 M02 M03 M04 M05 M06
Item Name SUB-PICTURE SUB-TINT SUB-COLOR SUB-BRIGHT SUB-SHARP V-SHIFT H-SHIFT RF-AGC V-SIZE PIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE SUB-COLOR(YUV) SUB-TINT(YUV) CC-POS (Vertical mode) SUB-VOL H-VCO MTS-ATT MTS-VCO MTS-FILTER MTS-WIDEBAND MTS-SPECTRAL SUB-VOL
IC 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip MICON 1 Chip 1 Chip 1 Chip MTS MTS MTS MTS MTS MTS
Register CONTRAST TINT COLOR BRIGHT VIDEO-TONE V-SHIFT H-PHASE RF-Delay V-SIZE VIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE COLOR BASEBAND-TINT V-MUTE,SERVICE A-ATT H-VCO ATT VCO FILTER WIDEBAND SPECTRAL VOL
7
Range 0~127 0~127 0~127 0~255 0~63 0~7 0~31 0~127 0~63 0~63 0~255 0~255 0~255 0~127 0~127 0~127 0~127 0~255 0, 1, 2 0~127 0~7 0~15 0~63 0~63 0~63 0~63 0~63
Default 127 64 64 128 32 4 16 127 32 32 127 127 127 64 64 64 64 32 0 127 4 10 32 28 27 32 63
21FL91
Ë SELF ADJUSTMENT H-VCO 1. 2. 3. 4. 5. 6. 7.
When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed. H-FREE(1chip) is set to 1. H-OUT is set by intelligent monitor output. IM input is set as TIM input. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC 1. 2. 3. 4.
When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed. AGC-OUT is set by intelligent monitor output. IM input is set as AD input. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the maximum setting value. 5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed. 6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated. 7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO 1. 2. 3. 4. 5. 6. 7.
When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed. VIF-DEF(1chip) is set to 1. AFC is set by intelligent monitor output. IM input is set as AD input. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
MTS-FILTER Adjustment is performed in the center of the range when FILTER status is OK. 1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B. 2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D. 3. (A+B+C+D)/4 is the adjustment point.
8
21FL91
Setting Mode Items No. F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 F45 F46 F47 F48 F49 F50 F51 F52 F53 F54
Item Name VideoTone-Gain (TV) VideoTone-Gain (AV) VideoTone-Gain(YUV) ABCL BS ABCL-G SHP-AV SHP-YUV RGB-CLIP E-SAVE FAO-VOL PIF-G Y-DELAY(TV) Y-DELAY(AV) Y-DELAY(YUV) TINT-AV COL-AV R-DRI(R2) R-DRI(R) R-DRI(B) B-DRI(R2) B-DRI(R) B-DRI(B) V-FREE GAMMA TRAP(TV) TRAP(AV) H-FREE 1W(TV) 1W(AV) YLPF BS-D BS-C SL(TV) SL(AV) SL(YUV) AFC2 VD(TV) VD(AV) AS(TV) AS(AV) AS(YUV) FBP(TV) FBP(AV) FBP(YUV) C.Clip Level PSW FAO-VOL CP CC LEVEL OSD POS OFFSET-ADJ-COL OFFSET-ADJ-TINT OFFSET-ADJ-TINT-YUV
IC 1chip 1chip 1chip 1chip 1chip 1chip OFFSET OFFSET 1chip OFFSET 1chip 1chip 1chip 1chip 1chip OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip 1chip MTS MTS PLL MICON MICON 1 chip 1 chip 1 chip
Register V-TONE V-TONE V-TONE ABCL BS-OFF ABCL-G VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) ExtRGB-Clip CONTRAST(OFFSET) A-ATT VIF-GAIN Y-Delay Y-Delay Y-Delay TINT(OFFSET) COLOR(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) V-FREE GAMMA TRAP-FINE TRAP-FINE H-FREE V.Window V.Window YSW-LPF BS-DISCHARGE BS-CHARGE S-SLICE DOWN S-SLICE DOWN S-SLICE DOWN AFC2-G Vsync-Det Vsync-Det Auto-Slice Auto-Slice Auto-Slice FBP Vth FBP Vth FBP Vth C.Clip Level PSW VOL CP
COLOR TINT BASEBAND-TINT
9
Range 0/1 0/1 0/1 0/1 0/1 0/1 -16~+16 -16~+16 0/1 0~63 0~127 0~7 0~7 0~7 0~7 -32~+32 -32~+32 -32~+32 -32~+32 -32 ~+32 -32~+32 -32~+32 -32~+32 0/1 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0~3 0~3 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0~63 0/1 0/1 0/1 -32~32 -32~32 -32~32
Default 0 0 0 0 0 0 0 0 0 30 120 4 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 60 0 0 0 0 0 0
21FL91
Option Mode Items No O01 O02 O03 O04 O05 O06 O07 O08 O09 O10 O11 O12 O13 O14 O15 O16 O17 O18 O19
ITEM DEM0 DOWNLOAD V-CHIP SPEAKER FAO P.PREF UNIV+ VIEW TIMER EZ-SETUP PON-CH FAV-COL COMPONENT AV AV2 MTS TONE-CTRL AUTO-OFF INIT-LANG SETUP-FLAG
O20
FR.AV (Front, Rear AV)
0 1 Without DEMO With DEMO Without V-CHIP OP With V-CHIP OP Without V-CHIP With V-CHIP Without SPEAKER With SPEAKER Without FAO With FAO Without P.PREF With P.PREF Without UNIV+ With UINIV+ Without VIEW TIMER With VIEW TIMER EZ-SETUP AUTO PRESET Without POWER-ON With POWER-ON FAV-COL COL-TEMP Without COMPONENT With COMPONENT Without AV With AV AV1 system AV2 system Without MTS With MTS Without S-ADJ With S-ADJ Without AUTO-OFF With AUTO-OFF ENGLISH SPANISH NO SETUP AUTO SETUP 3: Display "FRONT A/V INPUTS" and "REAR A/V INPUTS" in DEMO mode. 2: Display "FRONT A/V INPUTS" only in DEMO mode. 1: Display "REAR A/V INPUTS" only in DEMO mode. 0: No display of above lines in DEMO mode.
DEFAULT 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1
2
Check Mode Micron mask version, software version and ROM correction function status are displayed in check mode.
10
21FL91
ADJUSTMENT METHOD Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways is short the main chassis JA309 and JA402 There is three stage of Service Mode data First stage data from V01 ~ M06 to go into second stage of service mode data, press MENU key Second stage data from F01 ~ F54 to go into third stage of service mode data, press MENU key twice Third stage data from 001 ~ 020 Below is the contents of these data First Stage Data V01 V02 V03 V04 V05 V06 V07 V08 V09 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 M01 M02 M03 M04 M05 M06
Service Mode SUB-PICTURE SUB-TINT SUB-COLOR SUB-BRIGHT SUB-SHARP V-SHIFT H-SHIFT RF-AGC V-SIZE PIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE SUB-COLOR(YUV) SUB-TINT(YUV) CC-POS SCREEN CUT OFF SUB-VOL H-VCO MTS-ATT MTS-VCO MTS-FILTER MTS-WIDEBAND MTS-SPECTRAL SUB-VOL
Function CONTRAST TINT COLOR BRIGHT VIDEO-TONE V-SHIFT H-PHASE RF-DELAY V-SIZE VIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE COLOR BASEBAND-TINT CC-POSITION CUT OFF A-ATT H-VCO ATT (MTS) VCO (MTS) FILTER (MTS) WIDEBAND (MTS) SPECTRAL (MTS) VOL (MTS)
Auto Adjustment Item 1. H-VCO (Currently need manual adj) 2. RF-AGC 3. PIF-VCO 4. MTS-FILTER
11
Range 0~127 0~127 0~127 0~255 0~63 0~7 0~31 0~127 0~63 0~63 0~255 0~255 0~255 0~127 0~127 0~127 0~127 0~255 0~127 0~7 0~15 0~63 0~63 0~63 0~63 0~63
Default Data 127 64 64 128 32 4 16 127 32 32 127 127 127 64 64 64 64 32 0 127 4 10 32 28 27 32 63
21FL91
Second Stage Data F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 F45 F46 F47 F48 F49 F50 F51 F52 F53 F54
Service Mode VIDEO TONE -GAIN (TV) VIDEO TONE -GAIN (AV VIDEO TONE -GAIN(YUV) ABCL BS ABCL-G SHP-AV SHP-YUV SHP-CLIP E-SAVE FAO-VOL PIF-G Y-DELAY(TV) Y-DELAY(AV) Y-DELAY(YUV) TINT-AV COL-AV R-DRI(R2) R-DRI( R) R-DRI(B) B-DRI(R2) B-DRI( R) B-DRI(B) V-FREE GAMMA TRAP(TV) TRAP(AV) H-FREE 1W(TV) 1W(AV) YLPF BS-D BS-C SL(TV) SL(AV) SL(YUV) AFC2 VD(TV) VD(AV) AS(TV) AS(AV) AS(YUV) FBP(TV) FBP(AV) FBP(YUV) C.CLIP LEVEL PSW FAO-VOL CP CC LEVEL OSD POS COL OFFSET TINT OFFSET TING-YUV
Function V-TONE V-TONE V-TONE ABCL BS-OFF ABCL-G VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) EXTRGB-CLIP CONTRAST(OFFSET) A-ATT VIF-GAIN Y-DELAY Y-DELAY Y-DELAY TINT(OFFSET) COLOR(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) V-FREE GAMMA TRAP-FINE TRAP-FINE H-FREE V.WINDOW V.WINDOW YSW-LPF BS-DISCHARGE BS-CHARGE S-SLICE DOWN S-SLICE DOWN S-SLICE DOWN AFC2-G VSYNC-DET VSYNC-DET AUTO-SLICE AUTO-SLICE AUTO-SLICE FBP VTH FBP VTH FBP VTH C.CLIP LEVEL PSW VOL CHARGE PUMP CC LEVEL OSD POS (SUR → NOR) (SUR → NOR) TINT-YUV(OFFSET)
12
Range 0/1 0/1 0/1 0/1 0/1 0/1 -16~+16 -16~+16 0/1 0~63 0~127 0~7 0~7 0~7 0~7 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 0/1 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0~3 0~3 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0~63 0/1 0/1 0/1
Default Data 0 0 0 0 0 0 0 0 0 30 120 4 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 60 0 0 0 0 0 0
21FL91
Third Stage Data 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020
Service Mode DEMO DOWNLOAD V-CHIP SPEAKER FAO P.PREF UNIV+ VIEW TIMER EZ-SETUP *PON-CH FAV-COL COMPONENT AV AV2 MTS TONE-CTRL AUTO-OFF INIT-LANG SETUP-FLAG AV-FR
DATA="0" DEMO DISABLE V-CHIP OP DISABLE V-CHIP DISABLE SPEAKER DISABLE FAO DISABLE P.REF DISABLE UNIV+ DISABLE VIEW TIMER DISABLE EZ-SETUP POWER-ON DISABLE FAV-COL
DATA="1" ON ON ON ON ON ON ON ON AUTO PRESET ON COL-TEMP COMPONENT DISABLE ON AV DISABLE ON AV2 DISABLE ON MTS DISABLE ON S-ADJ DISABLE ON AUTO-OFF DISABLE ON ENGLISH SPANISH NO SET UP AUTO SET UP "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
* **POWER ON BY CH-UP/CH-DOWN KEY
13
Default Data 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 2
ADJUSTMENT PROCEDURE
14
001
002 0
0
1
1
FAO
1
DEF
21FL91
FUNCTION
1
1
AV
1
MTS
1
14-1
019 → “0”=NO SET UP “1”=AUTO SETUP
1
1
TONE AUTO LAN
016 017 018
“1”=COL-TEMP “1”=SPANISH
1
AV2
013 014 015
011 → ”0”=FAV-COL 018 → “0”=ENGLISH
1
COMP
FAV-COL
1
012
011
1
P.PREF UNIV+ VIEW
010
020
0
PON-CH
1
3
SETUP AV-FR
019
0
EZ
006 007 008 009
REFER AS BELOW
“0”=DISABLE “1”=ENABLE 009 → “0”=EZ-SETUP “1”=AUTO PRESET
1
SP
003 004 005
DEMO DOWNLOAD V-CHIP
BUS OPTION FOR THIRD STAGE SERVICE DATA
DEF
21FL91
FUNCTION
BUS OPTION FOR THIRD STAGE SERVICE DATA
OSD CHECKING
OUTPUT
–
CONTENT
21FL91
–
PRE-ADJUST REQUIREMENT
INPUT CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT POSITION
REFER AS BELOW
OPTION SET UP
ADJUSTMENT ITEM
ADJUSTMENT PROCEDURE
CP R-D(R2)
REFER AS BELOW
R-D(R)
50
2
R-D(B) B-D(R2)
5
B-D(R)
-7
B-D(B)
4
C-OF
1
TI-OF
1
1
1
SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV 1W(AV) SL(TV) VD(TV) AS(TV)
1
DEF
21FL91
+3
-2
-18
14-2
-8
+6
+10
+8
F54
+8
1
1
58
-8
SL(AV) AS(AV) FAO-VOL TINT-YUV
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA F19 F20 F21 F22 F23 F52 F53 F35 F41 F48 FUNCTION
DEF
21FL91
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA V05 F13 F14 F16 F17 F30 F34 F38 F40 F49 F18 FUNCTION
OSD CHECKING
OUTPUT
–
CONTENT 21FL91
–
PRE-ADJUST REQUIREMENT
INPUT CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT POSITION REFER AS BELOW
BUS SET UP
ADJUSTMENT ITEM
21FL91
US 4 CH LION HEAD (MONOSCOPE)
AC 220V, MEXICO MAGNETIC FIELD
CONFIRMATION BY CRT SCREEN
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST REQUIREMENT
0-31
15 15-1
[CHECKING SPEC] LEFT AND RIGHT SYMMETRICAL
A
B
1. ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B. 2. IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT B SLIDELY SMALLER THAN A
I2C BUS CONTROL
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V07
H-POSITION
ADJUSTMENT ITEM
US 4 CH LION HEAD AC 220V CONFIRMATION BY CRT SCREEN
CONTENT INPUT CONDITION OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
PRE-ADJUST REQUIREMENT
[CHECKING SPEC] OVERSCAN 10 ± 2.5%
15-2
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS SPECIFIED BELOW. CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE ADJUSTMENT.
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT POSITION V09
V-SIZE
ADJUSTMENT ITEM
21FL91
US 4 CH LION HEAD (MONOSCOPE PATTERN)
220V, RF INPUT, ZERO MAGNETIC FIELD
CONFIRMATION ON CRT SCREEN
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST REQUIREMENT
0-7
16 16-1
[CHECKING CONFIRMATION]
ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL POSITION. THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL POSITION NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD ENOUGH
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V06
V-PHASE
ADJUSTMENT ITEM
US 4 CH LION HEAD AC 220V CONFIRMATION ON CRT DISPLAY.
CONTENT INPUT CONDITION OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST REQUIREMENT
0~255
16-2
[CHECKING SPEC] LEFT AND RIGHT SYMMETRICAL
A
TEXT BOX BLK
B
1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED. 2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B.
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT POSITION V18
CLOSED CAPTION SET UP
ADJUSTMENT ITEM
21FL91
NO SIGNAL (RASTER) CONDITION
AC 220V
IC 801 PIN 11
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST REQUIREMENT
0-7
17
[CHECKING SPEC] FREQ = 15.735 ± 0.2 KHz
17-1
(SELF ADJ) 1) GO TO SERVICE MODE,BY SELECTING THE SERVICE DATA V21 2) PRESS THE R/C TO OPERATE AUTO H-VCO,OSD APPEAR "OK" AT SCREEN 3) IF APPEAR "NG" PLS REPEAT STEP2
(MANUAL ADJ) 1) GO TO SERVICE MODE, 2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V21
H-VCO
ADJUSTMENT ITEM
NO SIGNAL (RASTER) CONDITION AC 220V CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).
CONTENT INPUT CONDITION OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST REQUIREMENT
17-2
[CHECKING SPEC] 2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)
(AT MANUAL ADJUSTMENT MODE) 1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10 2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME AS SPECIFIED BELOW
(AT SELF ADJUSTMENT MODE) 1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10 2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT SCREEN 3) IF APPEAR “NG” PLS REPEAT STEP2
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT POSITION V10
PIF-VCO
ADJUSTMENT ITEM
21FL91
TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION
OUTPUT
ADJUSTMENT PROCEDURE
INPUT CONDITION
RF INPUT FIELD STRENGTH 53dBµV (FIX)
INPUT CONDITION
18
[CHECKING SPEC] MAX - 0.1V dc
18-1
(AT MANUAL ADJUSTMENT MODE) 1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE. 2. CHANGE THE ANTENNA INPUT SIGNAL TO 63-67 dBµV, AND MAKE SURE THERE IS NO NOISE 3. CHANGE THE ANTENNA INPUT SIGNAL TO 90-95 dBµV TO BE SURE THAT THERE IS NO CROSS MODULATION BEAT.
(AT SELF ADJUSTMENT MODE) 1. GO TO SERVICE MODE 2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN. 3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
CONTENT
US10CH HALF COLOR BAR
CONTENT
ADJUSTMENT PROCEDURE
OUTPUT
PRE-ADJUST REQUIREMENT
OPTION SET UP, BUS SET UP
PRE-ADJUST REQUIREMENT
CONTROL
ADJUSTMENT POSITION
I2C CONTROL
0-127
ADJUSTMENT ITEM
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V08
RF-AGC
ADJUSTMENT ITEM STEP RANGE
0-255
18-2
[VOLTAGE CONFIRMATION]
1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO 64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR IN CUT-OFF CONDITION 2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=RCUTOFF, V12=G-CUTOFF, V13=B-CUTOFF, FIX THE DATA OF THE COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BECOME WHITE. 3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE YMUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
CONFIRMATION ON CRT DISPLAY
220V
WINDOW PATTERN OR US4CH LION HEAD
OPTION SET UP, BUS SET UP
I2C CONTROL
V11,V12,V13
SCREEN
21FL91
23CH 501RE WINDOW PATTERN
220V
CRT SCREEN DISPLAY.
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN
PRE-ADJUST REQUIREMENT
0-127, 0~255
19 19-1
[CHECKING CONFIRMATION] X=0.273, Y=0.280 (11,600°K + 1 MPCD)
WHITE
US14
BLACK
1) WHITE (HIGH BEAM) FIRST LET THE GUN POINT AT BLACK POSITION (AS DRAWING ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH), ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280 2) BLACK (LOW BEAM) LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED AWAY FROM THE DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE. *WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING THIS ADJUSTMENT. **REPEAT STEP 1), 2) TO GET A REGULATED POSITION.
I2C BUS CONTROL
STEP RANGE
WHITE BALANCE
CONTROL
ADJUSTMENT V14,V15,V11,V12,V13 POSITION
ADJUSTMENT ITEM
ADJUSTMENT PROCEDURE
OUTPUT
INPUT CONDITION
CONTENT
PRE-ADJUST REQUIREMENT
CONTROL
ADJUSTMENT POSITION
ADJUSTMENT ITEM STEP RANGE
0-255
US14
19-2
[VOLTAGE CONFIRMATION] BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
BLACK
1) LET THE GUN POINT AT BLACK POSITION (AS ATTACH DRAWING), ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
CRT SCREEN DISPLAY.
220V
WINDOW PATTERN
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
I2C CONTROL
V04
SUB-BRIGHT
21FL91
WINDOW PATTERN
220V
CRT SCREEN DISPLAY.
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
PRE-ADJUST REQUIREMENT
20 20-1
[VOLTAGER CONFIRMATION] BRIGHTNESS Y=150 cd/m2
WHITE
US14
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING), ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2. NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH THE SPEC
I2C BUS CONTROL
0-127
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V01
SUB-PICTURE
ADJUSTMENT ITEM
US 10 CH HALF COLOR BAR PATTERN 220V B-AMP TR BASE (TP853) CONFIRRM WITH OSCILLOSCOPE
CONTENT INPUT CONDITION OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST REQUIREMENT
0-127
[CONFIRMATION]
20-2
B-AMP BASE (TP853) MUST BE IN STEPPING LEVEL
1) GET IN Y-MUTE FUNCTION BY R/C. 2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW. 3) DISABLE THE Y-MUTE **PLS TAKE NOTE THAT SERVICE MODE DATA F53 NEED TO SET +8
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT POSITION V02
SUB-TINT
ADJUSTMENT ITEM
21FL91
R-AMP TR BASE (TP851) CONFIRRM WITH OSCILLOSCOPE
OUTPUT
ADJUSTMENT PROCEDURE
OUTPUT
220V
INPUT CONDITION
21 Y
21-1
[CHECKING CONFIRMATION]
W
G
100% WHITE
Cy
Mg
R
B
*PLEASE TAKE NOTE THAT SERVICE DATA F52 MUST SET TO +10
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW 2) THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS OF COLOR BAR BEAT AT THE SAME LEVEL
INPUT CONDITION
US 10 CH HALF COLOR BAR PATTERN
CONTENT
ADJUSTMENT PROCEDURE
CONTENT
PRE-ADJUST REQUIREMENT
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TINT
PRE-ADJUST REQUIREMENT
CONTROL
ADJUSTMENT POSITION
I2C BUS CONTROL
0-127
ADJUSTMENT ITEM
CONTROL
STEP RANGE
ADJUSTMENT POSITION
V03
SUB-COLOR
ADJUSTMENT ITEM
–
STEP RANGE
–
24.5V
18.9± 1.1V DC
21-2
OPERATION VOLTAGE
TP VOLTAGE
[VOLTAGE CONFIRMATION]
[CAUTION] FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN RESET.)
[RECOVER INFORMATION] PULL OUT THE AC CORD.
[OPERATION CONFIRMATION] SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PROTECTOR IS FUNCTIONED. HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[VOLTAGE CONFIRMATION] CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.
SET THE USER CONTROL TO SHIPMENT POSITION.
CONFIRMATION BY THE CRT
AC 220V, RF INPUT
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AFTER ALL ADJUSTMENT FINISHED.
–
X-RAY PROTECTION OPERATING CONFIRMATION
21FL91
AC 220V, RF INPUT
CRT ANODE VOLTAGE
INPUT CONDITION
OUTPUTΩ
ADJUSTMENT PROCEDURE
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
–
22 22-1
[CAUTION POINT] USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/ DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
BELOW 30kV
HIGH VOLTAGE
SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH ON Y-MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT POSITION
–
HIGH VOLTAGE
ADJUSTMENT ITEM
ADJUSTMENT PROCEDURE
OUTPUT
INPUT CONDITION
CONTENT
PRE-ADJUST REQUIREMENT
CONTROL
ADJUSTMENT POSITION
ADJUSTMENT ITEM STEP RANGE
0~15
22-2
[CHECKING SPEC] 490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)
1) SET THE SOUND VOLUME CONTROL MORE THAN 1. 2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BECOME AS SPECIFIED BELOW.
IC 3001 39 PIN
AC 220V, RF INPUT
MONORAL SIGNAL (400HZ 100% MODULATION)
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
I2C BUS CONTROL
M01
MS LEVEL ADJUSTMENT
21FL91
SIGNAL WITHOUT NOISE (SIGNAL WITHOUT SOUND MODULATION)
AC 200V
IC 3001 39 PIN
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST REQUIREMENT
23 23-1
[CHECKING SPEC] 62.94 ± 0.75kHz (CHECKING SPEC : 62.94 ± 1.20kHz)
1) CONNECT 100 µ F ELECTROLLYTIC CAPACITOR BETWEEN C3005 (-ve)-GND 2) ADJUST THE BUS DATA M02 UNTIL THE OUTPUT FREQUENCY OF 39 PIN BECOME AS SPECIFIED BELOW. NOTE: TO MINIMIZE THE PRODUCTION TIME, ITEM 1) CAN IGNORE. IF ITEM 2) CAN'T BE ADJUST, THEN ITEM 1) IS REQUIRE.
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT POSITION
M02
MTS+VCO ADJUSTMENT
ADJUSTMENT ITEM
ADJUSTMENT PROCEDURE
OUTPUT
INPUT CONDITION
CONTENT
PRE-ADJUST REQUIREMENT
CONTROL
ADJUSTMENT POSITION
ADJUSTMENT ITEM STEP RANGE
0~63
23-2
[CHECKING SPEC] REFER TO ABOVE (CHECKING SPEC : ± 2 STEP TO CENTRE)
1) ADJUST M03 DATA UNITILL OK DISPLAY ON SCREEN ADJUST THE BUS DATA IN CENTRE OF THE RANGE.
CONFIRM BY CRT SCREEN
PIN 14 (FROM C3005 - TERMINAL)
SINE WAVE (9.4kHz, 600mVrms)
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO
I2C BUS CONTROL
M03
FILTER ADJUSTMENT
21FL91
STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
RF INPUT
IC 3001 39 PIN
CONTENT
INPUT CONDITION
OUTPUT
ADJUSTMENT PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER
PRE-ADJUST REQUIREMENT
24 24-1
[CHECKING SPEC] OVER 25 dB (CHECKING SPEC : OVER 20 dB)
SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC AS SPECIFIED BELOW.
1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNTIL THE AC VOLTAGE OF 39 PIN BECOME MINIMUM LEVEL. 2) INPUT SIGNAL 2, ADJUST BUS DATA OF M05 UNTIL THE AC VOLTAGE OF 39 PIN BECOME MINIMUM LEVEL. 3) REPEAT STEP 1) AND 2).
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT POSITION
M04, M05
SEPARTION ADJUSTMENT
ADJUSTMENT ITEM
24-2
21FL91
21FL91
-MEMO-
25
21FL91
CHASSIS LAYOUT H
G
F
E
D
C
B
A
1
2
3
4
26
5
6
21FL91
CRT BLOCK DIAGRAM H
G
F
E
D
C
B
A
1
2
3
4
27
5
6
21FL91
21FL91
MAIN BLOCK DIAGRAM J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
28~29
12
13
14
15
16
17
18
19
20
21FL91
21FL91
MTS BLOCK DIAGRAM J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
30~31
12
13
14
15
16
17
18
19
20
21FL91
DESCRIPTION OF SCHEMATIC DIAGRAM WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar
NOTES:
1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ) 2. All resistors are 1/16 watt, unless otherwise noted. 3. All capacitors are µF, unless otherwise noted. (P=pF=µµF) 4. (G) indicates ±2% tolerance may be used. 5. indicates line isolated ground.
signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
VOLTAGE MEASUREMENT CONDITIONS: å AND SHADED (
) COMPONENTS = SAFETY RELATED PARTS. ç MARK= X-RAY RELATED PARTS.
1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. All voltages measured with 1000µ V B & W or Color signal.
DRGANNES MARQUES åET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ç : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
WAVEFORMS
32
21FL91
SCHEMATIC DIAGRAM: CRT Unit H
G
F
E
D
C
B
A
1
2
3
4
33
5
6
21FL91
21FL91
SCHEMATIC DIAGRAM: MAIN Unit J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
34~35
12
13
14
15
16
17
18
19
20
21FL91
21FL91
SCHEMATIC DIAGRAM: MTS MODULE Unit J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
36~37
12
13
14
15
16
17
18
19
20
21FL91
PRINTED WIRING BOARD ASSEMBLIES H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
38
5
6
21FL91
H
RJ 4 0 R1 0 2 6 RJ 4 1
RJ 4 5 RJ 4 3
R3 8 4
R3 8 3
RJ 1 6
R3 8 2
R1 0 0 2
R1 0 0 9
R4 3 1
R1 0 0 7
R4 3 2
RJ 4 6
R1 0 0 6
R1 0 0 8
RJ 4 8
R1 0 2 7 R1 0 0 3 R3 8 1
RJ 6 0
B2
Z1
A1
R3 2 1
G
RJ 3 0
F DC2
RJ 7 1
R3 1 5
C3 1 9
C3 1 3
R3 1 3
R3 1 4
RJ 1 1
R3 1 2
RJ 5 9
RJ 7 6
C3 2 0 RJ 9 RJ 0 R3 11 0 RJ 8
RJ 1 3
R3 0 6
R3 0 5 RJ 1 5
F
R3 1 6 RJ 2 1
Q3 0 1
Q3 0 2
C3 0 8
R3 0 7 R3 1 7 RJ 1 4
R3 1 0 R3 1 8
R3 0 8 RJ 7 7 R3 0 3
RJ 7 0
RJ 7 4
C7 5 9
R1 0 8 1 R7 6 8
R1 0 5 9
Q7 4 1
R7 6 6
Q7 5 5
R7 4 4
R4 5 4
R7 4 3
R1 0 5 2 R1 0 4 3
D1 0 0 4
D1 0 9 0
R1 0 3 3
R1 0 4 9
R1 0 4 7
R1 0 5 3
R1 0 7 6
Q7 4 0
R1 0 3 8
R1 0 5 7 RJ 6 9
R1 0 3 6
R1 0 3 7
R1 0 5 4
D1 0 8 8
R1 0 7 3
RJ 2 3
R1 0 3 9
R1 0 6 5 R1 0 5 6
Q1 0 0 1
R1 0 2 4
R1 0 4 6
R1 0 6 4
R1 0 5 1
D1 0 8 6
D1 0 8 5
Q1 0 0 2
R1 0 3 4
R1 0 4 8
E
RJ 3 6
C1 0 1 5
R1 0 5 5
R1 0 7 2
I C1 0 0 1 RJ 3 9
RJ 3 3
C1 0 0 4 R1 0 7 4
RJ 1 7
D1 0 8 7
RJ 3 5
R1 0 2 5
R1 0 7 1
C7 8 4
F DC3 R1 0 7 5
R1 0 7 0
R1 0 6 9
R1 0 6 8
C1 0 1 3
RJ 6 3
R1 0 3 1 R1 0 2 1
R1 0 2 2
R1 0 6 7
R1 0 6 6
C1 0 1 0
R8 4 2
C1 8 5 5
C8 1 0
C1 0 0 8
R7 1 4
R6 6 2
C1 0 0 9
R1 0 6 0
C7 3 5
C1 0 1 1
R1 0 3 2
R1 0 6 1
RJ 3 2
Q6 0 4
RJ 2 2
I C1 0 0 3
RJ 1 9
R6 6 1
R1 0 6 3
D8 1 0
C8 0 9
R8 0 4
R1 8 5 1
R8 0 5
R1 8 5 2
R8 4 3
RJ 4 2
C8 0 8
C8 0 6
R8 4 0
C8 1 1
R8 3 8 D8 1 2
R8 0 2
D8 1 5
C8 1 4
R8 1 3
R8 0 6
R1 8 5 3
C8 1 3
C8 1 6
C8 1 5
Q8 0 3
R8 0 7
R8 1 0
R1 0 6 2
Q8 0 4
D8 1 1
D8 1 4
R8 3 2
RJ 3 7
D8 1 3
C8 1 2
R8 1 1 R8 1 6
RJ 6 2 R8 3 4
R8 1 4
R8 1 5
R8 1 7
RJ 7 5
R8 3 9 D5 0 1
C8 0 2
C8 0 4
R8 1 2
C8 2 1
C8 2 3
C5 1 9
R5 2 0
D
R8 0 1
R8 0 3
I C8 0 1 C8 1 9 R5 2 7
R8 3 5
R5 2 8 RJ 7
C8 4 6
RJ 2 6
R8 2 1
C2 1 1
R2 1 3
RJ 6 5
R2 1 2
C8 4 5
R2 RJ120
R8 2 2
C8 3 1
D2 0 2 R8 1 9
C8 4 R8 34 0
C2 1 3
C8 4 4
R5 2 1 C8 4 1
RJ 3
C8 4 7
R2 1 1
R8 3 C8 42 5
C2 1 0
R8 2 0
C8 3 3 R8 3 3
R1 8 5 4
Q2 0 2
C8 3 6
R8 2 5
RJ 4 9
RJ 3 8
C1 8 5 6
R5 1 6
C5 1 7
C8 4 0
R5 2 2
RJ 5 0
C2 0 8
RJ 4 4
R5 0 4
R2 0 9
C2 0 7
R2 0 8 R2 2 0 Q2 0 1 C2 0 9 R2 0 7 R2 0 6
R2 0 5
RJ 1
R1 8 5 0
R8 3 1
C5 1 8
RJ 1 2 R4 3 7
R8 2 8 R8 2 7
R1 RJ82459
C8 3 9
R8 2 9
RJ 4 7
C4 3 6
I C4 0 1
C2 1 2
Q8 0 5
C2 0 5
RJ 2 4
C
RJ 7 2
RJ 7 3
F DC4 C2 0 3
RJ 5 3
RJ 5 1
RJ 3 4
R3 6 5
R3 6 3 RJ 5 2
R3 6 2
R6 1 9
R6 1 8
C1 8 6 2
C1 8 6 4
C1 8 6 1
R1 8 6 1
R2 0 1
RJ 6 4
R6 2 0
R3 6 4
C1 8 6 3
R2 0 2
R1 8 6 2
F DC1
R8 3 0
RJ 6 2 R4 1
R4 3 5
R6 1 7
R6 5 4
Z2
R4 3 3
R4 3 4
R4 5 8
B1
R4 6 1
A2
R6 1 3
B
PWB-A: MAIN Unit (Chip Parts Side)
A
1
2
3
4
39
5
6
21FL91
H
G
F
E
D
C
PWB-B: CRT Unit (Wiring Side)
B
A
1
2
3
4
40
5
6
21FL91
H
G
F
PWB-E: MTS MODULE Unit (Wiring Side) E
R3 0 2 4
RJ 1 0
R3 0 8 0
R3 0 2 5
D RJ 4
R3 0 8 1
Q3 0 0 7
R3 0 1 6
R3 0 0 4
R3 0 0 3
C3 0 0 2
I C3 0 0 2
R3 0 0 5
C3 0 0 8
R3 0 8 5
RJ 1 3
R3 0 8 4
C3 0 8 2
R3 03 RJ 76
RJ 2
Q3 0 0 6 RJ 6
I C3 0 0 1
R3 0 0 7
R3 0 1 9
R3 0 0 8 R3 0 8 2
RJ 1 4
R3 0 0 1
R3 0 0 2
RJ 3
R3 0 1 0
C3 0 1 3
R3 0 1 8
R3 0 8 3
R3 0 2 6
C3 0 3 1
R3 0 2 9
C3 0 3 2
C3 0 2 6
Q3 0 0 4 C3 0 2 8
C3 0 4 3
R3 0 1 1 C3 0 3 3
C3 0 2 3 R3 0 1 3
Q3 0 0 1
R3 0 3 5
R3 0 3 4
C3 0 3 5
C3 0 3 6
C3 0 2 4
R3 0 2 7
R3 0 1 2
C3 0 2 7
C3 0 2 5
C
Q3 0 0 2
R3 0 3 0
R3 0 2 8
C3 0 4 2
R3 0 2 1 Q3 0 0 5 R3 RJ 03 83
R3 0 3 2
R3 0 1 4
RJ 9
R3 0 3 1
RJ 1 5
RJ 1 7
RJ 1 6
PWB-E: MTS MODULE Unit (Chip Parts Side)
B
A
1
2
3
4
41
5
6
21FL91
Ref. No. Part No. ★ Description Code REPLACEMENT PARTS LIST
PARTS REPLACEMENT Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
Ref. No. å Q701 Q703 Q740 Q741 Q751 Q752 Q753 Q755 Q804 Q805 Q1001
VSSTP6NC80Z1E VS2SC3198-Y-1+ VS2SD601AR/-1~ VS2SD601AR/-1~ VS2SC2236Y/-1+ VS2SC2236Y/-1+ VS2SC3198-G-1+ VS2SD601AR/-1~ VS2SB709AR/-1~ VS2SD601AR/-1~ VS2SD601AR/-1~
D201 D203 D393 D501 D502 D503 D504 D505 D510 D601 D602 D603 D606 D608 å D701 D703 D704 D708 D710 D750 D751 D752 D755 D756 D801 D806 D807 D808 D810 D811 D812 D813 D815 D1004 D1081 D1085 D1086 D1087 D1088 D1089 D1090 D1091 å IC702 VA701
RH-EX0676GEZZ~ RH-DX0048GEZZ~ RH-DX0247CEZZ~ RH-EX1393CEZZ~ RH-EX0652GEZZ~ RH-EX0612GEZZ~ RH-EX0654CEZZ~ RH-DX0441CEZZ~ RH-DX0131CEZZ~ RH-DX0048GEZZ~ VHD1SS244//-1~ RH-EX0662GEZZ~ RH-DX0131CEZZ~ RH-DX0131CEZZ~ RH-DX0111PEZZ RH-DX0048GEZZ~ RH-EX0650GEZZ~ RH-DX0048GEZZ~ RH-DX0048GEZZ~ RH-EX0647CEZZ~ RH-DX0229CEZZ RH-DX0131CEZZ~ RH-DX0048GEZZ~ RH-DX0441CEZZ~ RH-EX0613GEZZ~ RH-DX0048GEZZ~ RH-EX0625GEZZ~ RH-DX0048GEZZ~ RH-EX0263TAZZ~ RH-EX0263TAZZ~ RH-EX0263TAZZ~ RH-EX1393CEZZ~ RH-EX0263TAZZ~ RH-EX1393CEZZ~ RH-DX0048GEZZ~ RH-EX1393CEZZ~ RH-EX1393CEZZ~ RH-EX1393CEZZ~ RH-EX1393CEZZ~ RH-EX0613GEZZ~ RH-EX1393CEZZ~ RH-DX0048GEZZ~ RH-FX0008GEZZ RH-VX0073CEZZ
å PR701 å R751 å R752 X801
RMPTP0001PEZZ RR-DZ0049CEZZ~ RR-DZ0049CEZZ~ RCRSAA009WJZZ
"HOW TO ORDER REPLACEMENT PARTS"
MARK Ref. No.
2. REF. NO. 4. DESCRIPTION
: SPARE PARTS-DELIVERY SECTION. ★
Part No.
Description
Code
PICTURE TUBE å V101 å L706
VB51QDX992X2E RCiLG0069PEZZ QEARCA012WJZZ PMAGF3046CEZZ PSPAG0003PEZZ
X X X X X
Picture Tube Degaussing Coil Grounding Strap Purity Magnet, x3 Spacer, x3
BY AH AC AC AB
PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) PWB-A DUNTKB541WEA0 - MAIN Unit PWB-B DUNTKA599WEA0 - CRT Unit PWB-E DUNTKB271WEA1 - MTS MODULE Unit
— — —
DUNTKB541WEA0 PWB-A MAIN UNIT TUNER NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY NOT INDEPENDENTLY. å TU201 RTUNQA003WJZZ X Tuner AR
INTEGRATED CIRCUITS IC301 IC401 å IC501 IC601 å IC701 å IC703 IC801 IC1001 IC1003
VHiAN7522++-1 VHiMM1501XN-1~ VHiTDA9302H-1 VHiKA7809AP-1 VHiTEA1507/-1 VHiSE130N//-1 VHiM61251FP1EQ RH-iXA155WJN4 VHiBR2416E2-1~
X X X X X X X X X
AN7522++ MM1501XN TDA9302H KA7809AP TEA1507 SE130N M61251FP IXA155WJ BR2416E2
AF AC AE AB AE AF AN AP AD
VS2SC2735//1E~ VS2SD601AR/-1~ VS2SC2482//-1+ VS2SD2539//1E VS2SC3198-G-1+ VS2SD601AR/-1~
X X X X X X
2SC2735 2SD601AR 2SC2482 2SD2539 2SC3198-G 2SD601AR
STP6NC80Z 2SC3198-Y 2SD601AR 2SD601AR 2SC2236Y 2SC2236Y 2SC3198-G 2SD601AR 2SB709AR 2SD601AR 2SD601AR
Code AF AB AA AA AB AB AB AA AA AA AA
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Zener, EX0676GE DX0048GE DX0247CE Zener, EX1393CE Zener, EX0652GE Zener, EX0612GE Zener, EX0654CE DX0441CE DX0131CE DX0048GE 1SS244 Zener, EX0662GE DX0131CE DX0131CE DX0111PE DX0048GE Zener, EX0650GE DX0048GE DX0048GE Zener, EX0647CE DX0229CE DX0131CE DX0048GE DX0441CE Zener, EX0613GE DX0048GE Zener, EX0625GE DX0048GE Zener, EX0263TA Zener, EX0263TA Zener, EX0263TA Zener, EX1393CE Zener, EX0263TA Zener, EX1393CE DX0048GE Zener, EX1393CE Zener, EX1393CE Zener, EX1393CE Zener, EX1393CE Zener, EX0613GE Zener, EX1393CE DX0048GE PC123FY8 Varistor
AB AA AB AB AB AB AC AA AB AA AA AB AB AB AC AA AB AA AA AE AB AB AA AA AB AA AB AA AB AB AB AB AB AB AA AB AB AB AB AB AB AA AB AB
PACKAGED CIRCUITS X X X X
Packaged Circuit Resistor Resistor Crystal, CRSAA009WJ
AE AB AB AC
FILTERS
TRANSISTORS Q201 Q302 Q601 Q602 Q603 Q604
X X X X X X X X X X X
Description
DIODES AND LED
To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 3. PART NO.
★
Part No.
AB AA AB AG AB AA
CF201 CF802 SF201
RFiLC0447CEZZ RFiLC0446CEZZ RFiLC0405CEZZ
X Filter, FiLC0447CE X Filter, FiLC0446CE X Filter, FiLC0405CE
L202 L203
VP-CF270K0000~ X Peaking, 27µH 10% VP-DF270K0000~ X Peaking, 27µH 10%
AB AB AD
COILS
42
AB AA
21FL91
Part No.
★
L204 L602 L603 å L703 L751 L801 L802 L803 L804 L806 L807 L1861 L1862
VP-XF1R2K0000~ RCiLP0223CEZZ RCiLZA006WJZZ RCiLF0078PEZZ RCiLP0225CEZZ VP-DF100K0000~ VP-DF100K0000~ VP-DF100K0000~ VP-XF150K0000~ VP-DF100K0000~ VP-XF1R2K0000~ VP-XF8R2K0000~ VP-XF8R2K0000~
X X X X X X X X X X X X X
å T601 å T602 å T701
RTRNZ0026PEZZ X Transformer RTRNFA012WJZZ X H-Volt Transformer RTRNWA076WJZZ X Transformer
Ref. No.
Description Peaking, 1.2µH 10% Coil, CiLP0223CE Coil, CiLZA006WJ Coil, CiLF0078PE Coil, CiLP0225CE Peaking, 10µH 10% Peaking, 10µH 10% Peaking, 10µH 10% Peaking, 15µH 10% Peaking, 10µH 10% Peaking, 1.2µH 10% Peaking, 8.2µH 10% Peaking, 8.2µH 10%
Code AA AB AE AC AB AA AA AA AA AA AA AA AA
C643 C650 å C701 C702 C703 C704 å C705 C706 C711 C718 C737 C738 C743 C744 C751 C752 C753 C754 C755 C756 C758 C759 C784 C801
TRANSFORMERS AD AU AG
CAPACITORS C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C213 C301 C304 C307 C308 C310 C311 C312 C313 C321 C322 C377 C391 C392 C393 C434 C435 C436 C452 C505 C508
VCEA0A1CW476M+ X VCEA0A0JW477M+ X VCKYCY1HF103Z~ X VCEA0A0JW477M+ X VCKYCY1HF103Z~ X VCEA0A1HW106M+ X VCKYCY1HF103Z~ X VCKYCY1HF103Z~ X VCKYCY1HF103Z~ X VCKYCY1HF103Z~ X VCKYCY1HB102K~ X VCEA0A1CW477M+ X VCEA0A1CW106M+ X VCEA0A1HW105M+ X VCKYCY1HF153Z~ X VCEA0A1HW225M+ X VCEA0A1HW105M+ X VCEA0A1CW476M+ X VCKYCY1HF153Z~ X VCEA0A1CW476M+ X VCEA0A1HW105M+ X VCEA0A1CW107M+ X VCKYPA1HB102K+ X VCQYTA1HM103J+ X VCEA0A1EW108M+ X VCEA0A1CW106M+ X VCE9GA1CW106M+ X VCKYCY1HF103Z~ X VCEA9M1CW106M+ X VCEA0A1HW107M+ X VCFYAA2AA224J+ X
C509 C511 C512 C513 C514
VCKYD41CY103N~ VCEA0A1VW477M+ VCKYPA2HB102K+ VCEA0A1VW108M+ VCFYSA1JB273J+
X X X X X
C515 C518 C519 C601 C602 C603 C604 C605 C606 å C607
VCEACA1HC335J+ X VCKYCY1HF103Z~ X VCKYCY1HB102K~ X VCQYTA1HM563J+ X VCEA0A1HW475M+ X VCEA0A1HW105M+ X VCEA0A2EW336M+ X VCKYPA2HB102K+ X VCKYPA2HB102K+ X VCFPVC3ZA902H X
C608 C610
VCKYPA2HB561K+ X VCFYSB2EB823J X
C611
VCFPVC2DB244J
C641 C642
VCEA0A1EW108M+ X VCEA0A1EW476M+ X
X
47 16V Electrolytic 470 6.3V Electrolytic 0.01 50V Ceramic 470 6.3V Electrolytic 0.01 50V Ceramic 10 50V Electrolytic 0.01 50V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 1000p 50V Ceramic 470 16V Electrolytic 10 16V Electrolytic 1 50V Electrolytic 0.015 50V Ceramic 2.2 50V Electrolytic 1 50V Electrolytic 47 16V Electrolytic 0.015 50V Ceramic 47 16V Electrolytic 1 50V Electrolytic 100 16V Electrolytic 1000p 50V Ceramic 0.01 50V Mylar 1000 25V Electrolytic 10 16V Electrolytic 10 16V Electrolytic 0.01 50V Ceramic 10 16V Electrolytic 100 50V Electrolytic 0.22 100V Metallized Polypro Film 0.01 16V Ceramic 470 35V Electrolytic 1000p 500V Ceramic 1000 35V Electrolytic 0.027 63V Metallized Polypro Film 3.3 50V Electrolytic 0.01 50V Ceramic 1000p 50V Ceramic 0.056 50V Mylar 4.7 50V Electrolytic 1 50V Electrolytic 33 250V Electrolytic 1000p 500V Ceramic 1000p 500V Ceramic 9000p 1800V MetalIized Polypro Film 560p 500V Ceramic 0.082 250V MetalIized Polypro Film 0.24 200V MetalIized Polypro Film 1000 25V Electrolytic 47 25V Electrolytic
Ref. No.
AA AB AA AB AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AB AA AB AA AA AB AC
C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C831 C833 C834 C835 C836 C837 C839 C840 C841 C842 C843 C845 C846 C847 C848 C1001 C1003 C1004 C1006 C1007 C1008
AA AB AB AA AB AB AA AA AA AA AA AB AB AB AB AB AB AB AB AA
43
Part No.
★
Description
VCEA0A1CW477M+ X 470 16V Electrolytic VCKYPA2HB101K+ X 100p 500V Ceramic RC-FZ029SCEZZ X 0.22 275V Metallized Polypro Film RC-KZ0029CEZZ+ X 0.01 250V Ceramic RC-KZ0029CEZZ+ X 0.01 250V Ceramic RC-KZ0029CEZZ X 0.01 250V Ceramic RC-EZ0804CEZZ X 220 400V Electrolytic VCQYTA1HM103J+ X 0.01 50V Mylar VCFYFA1HA334J+ X 0.33 50V Metallized Polypro Film VCKYPA2HB472K+ X 4700p 500V Ceramic VCEA0A1EW226M+ X 22 25V Electrolytic RC-KZ0040CEZZ X 820p 2kV Ceramic VCKYPH3DB561K X 560p 2000V Ceramic VCQYTA1HM104J+ X 0.1 50V Mylar RC-KZ0106GEZZ X 0.0033 250V Ceramic VCKYPH3DB561K X 560p 2000V Ceramic RC-EZ0724CEZZ X 100 160V Electrolytic RC-EZ0638CEZZ X 33 160V Electrolytic VCQYTA1HM103J+ X 0.01 50V Mylar VCEA0A1EW108M+ X 1000 25V Electrolytic VCEA0A1HW225M+ X 2.2 50V Electrolytic VCKYCY1HB102K~ X 1000p 50V Ceramic VCKYCY1HB103K~ X 0.01 50V Ceramic VCFYFA1HA105J+ X 1 50V Metallized Polypro Film VCKYCY1HF103Z~ X 0.01 50V Ceramic VCEA0A1AW476M+ X 47 10V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCEA0A1HW105M+ X 1 50V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCEA0A1CW337M+ X 330 16V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCEA0A1AW107M+ X 100 10V Electrolytic VCEA0A1HW475M+ X 4.7 50V Electrolytic VCCCCY1HH121J~ X 120p 50V Ceramic VCEA0A1HW474M+ X 0.47 50V Electrolytic VCKYCY1HF153Z~ X 0.015 50V Ceramic VCE9GA1HW105M+ X 1 50V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCEA0A1CW337M+ X 330 16V Electrolytic VCE9EM1HW105M+ X 1 50V Electrolytic VCKYPA1HF103Z+ X 0.01 50V Ceramic VCEA9M1CW476M+ X 47 16V Electrolytic VCKYPA1HB103K+ X 0.01 50V Ceramic VCEA0A1CW476M+ X 47 16V Electrolytic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCEA0A1CW107M+ X 100 16V Electrolytic VCEA0A1CW106M+ X 10 16V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCEA0A1HW105M+ X 1 50V Electrolytic VCCCCY1HH680J~ X 68p 50V Ceramic VCKYCY1EF104Z~ X 0.1 25V Ceramic VCCCCY1HH101J~ X 100p 50V Ceramic VCEA9M1HW474M+ X 0.47 50V Electrolytic VCEA9M1HW105M+ X 1 50V Electrolytic VCKYCY1CF224Z~ X 0.22 16V Ceramic VCKYCY1HF103Z~ X 0.01 50V Ceramic VCCCCY1HH220J~ X 22p 50V Ceramic VCEA0A1HW105M+ X 1 50V Electrolytic VCEA0A0JW107M+ X 100 6.3V Electrolytic VCEA0A1CW106M+ X 10 16V Electrolytic VCKYCY1CF474Z~ X 0.47 16V Ceramic VCEA0A1HW225M+ X 2.2 50V Electrolytic VCEA0A1CW107M+ X 100 16V Electrolytic VCKYCY1HF103Z~ X 0.01 50V Ceramic
Code AB AB AB AB AB AB AH AA AB AB AA AB AB AB AB AB AC AD AA AB AA AA AA AB AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AB AB AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
21FL91
Ref. No.
★
Part No.
C1009 C1011 C1012 C1013 C1014 C1015 C1081 C1849
VCKYCY1HF103Z~ X VCKYCY1HB221K~ X VCEA0A1HW105M+ X VCKYCY1HB102K~ X VCEA0A1HW475M+ X VCCCCY1HH101J~ X VCEA0A1HW104M+ X VCFYFA1HA223J+ X
C1855 C1856 C1861 C1862 C1863 C1864
VCKYCY1HB561K~ VCKYCY1HB102K~ VCCCCY1HH221J~ VCKYCY1HB102K~ VCCCCY1HH221J~ VCKYCY1HB102K~
C211 RJ1 RJ2 RJ3 RJ4 RJ7 RJ9 RJ10 RJ11 RJ13 RJ14 RJ15 RJ16 RJ17 RJ19 RJ22 RJ23 RJ33 RJ35 RJ37 RJ39 RJ41 RJ42 RJ43 RJ47 RJ50 RJ51 RJ52 RJ53 RJ60 RJ62 RJ63 RJ65 RJ69 RJ70 RJ71 RJ72 RJ75 RJ76 R201 R202 R205 R206 R207 R208 R209 R216 R220 R301 R302 R303 R304 R305 R307 R308 R310 R311 R314 R315
VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF000J~ VRS-CY1JF101J~ VRS-CY1JF101J~ VRS-CY1JF680J~ VRS-CY1JF122J~ VRS-CY1JF221J~ VRS-CY1JF331J~ VRS-CY1JF392J~ VRS-VV3LB333J VRS-CY1JF221J~ VRS-CY1JF102J~ VRN-RL3DBR22J+ VRS-CY1JF103J~ VRD-RA2BE683J~ VRS-CY1JF274J~ VRS-CY1JF222J~ VRS-CY1JF332J~ VRS-CY1JF473J~ VRD-RA2BE272J~ VRS-CY1JF332J~ VRS-CY1JF222J~
X X X X X X
Description 0.01 50V Ceramic 220p 50V Ceramic 1 50V Electrolytic 1000p 50V Ceramic 4.7 50V Electrolytic 100p 50V Ceramic 0.1 50V Electrolytic 0.022 50V Metallized Polypro Film 560p 50V Ceramic 1000p 50V Ceramic 220p 50V Ceramic 1000p 50V Ceramic 220p 50V Ceramic 1000p 50V Ceramic
Code
Ref. No.
Part No.
★
AA AA AA AA AA AA AA AA
R362 R363 R364 R365 R381 R382 R383 R384 R431 R432 R433 R434 R435 R437 R461 R462 R502 R503 R504 R506 R507 R513 R514 R520 R522 R523 R524 R525 R526 R528 R602 R603 R604 R605 R606 R608 R611 R612 R613 R614 R615 R616 R617 R618 R621 R622 R631 R632 R633 R637 R638 R639 R642 R643 R661 R662 R701 R702 R705 R706 R707 R708 R710 R711 R713 R715 R716 R720 R725 R726 R742 R743 R744 R745 R746 R753
VRS-CY1JF332J~ VRS-CY1JF564J~ VRS-CY1JF332J~ VRS-CY1JF564J~ VRS-CY1JF564J~ VRS-CY1JF332J~ VRS-CY1JF564J~ VRS-CY1JF332J~ VRS-CY1JF101J~ VRS-CY1JF750J~ VRS-CY1JF750J~ VRS-CY1JF750J~ VRS-CY1JF750J~ VRS-CY1JF101J~ VRS-CY1JF750J~ VRS-CY1JF101J~ VRS-RG3AB102J+ VRN-RL3DB1R2J+ VRS-CY1JF222J~ VRS-RG3AB331J+ VRD-RM2HD1R0J~ VRD-RM2HD333J~ VRD-RM2HD682J~ VRS-CY1JF123J~ VRS-CY1JF101J~ VRD-RA2BE101J~ VRD-RA2BE103J~ VRD-RA2BE122J~ VRD-RA2BE101J~ VRS-CY1JF683J~ VRD-RA2BE393J~ VRD-RA2BE273J~ VRD-RA2BE473J~ VRD-RM2HD104J~ VRN-RL3LBR27J+ VRD-RM2HD102J~ VRN-RL3ABR27J+ VRD-RM2HD270J~ VRS-CY1JF000J~ VRD-RA2BE154J~ VRD-RA2BE102J~ VRD-RA2BE102J~ VRS-CY1JF123J~ VRS-CY1JF103J~ VRN-RL2HC4R7J+ VRS-VV3DB682J VRS-KT3LB391J VRS-RG3LB122J+ VRS-KA3NG3R3K VRD-RA2BE331J~ VRD-RA2BE331J~ VRD-RM2HD562J~ VRD-RM2HD470J~ VRS-KA3HG912J VRS-CY1JF102J~ VRS-CY1JF103J~ VRW-KQ3NC1R5K VRD-RM2HD100J~ VRN-VV3DBR33J VRN-VV3DBR27J VRD-RM2HD270J~ VRD-RA2BE102J~ VRS-RG2HC103J+ VRD-RA2BE394J~ VRD-RM2HD122J~ VRD-RA2BE150J~ VRD-RA2BE223J~ VRW-GA4AB1R5K VRD-RM2HD821J~ VRN-RL2HCR47J+ VRD-RA2BE183J~ VRS-CY1JF332J~ VRS-CY1JF332J~ VRD-RA2BE472J~ VRD-RA2BE223J~ VRD-RM2HD124J~
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
AA AA AA AA AA AA
RESISTORS X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 100 68 1.2k 220 330 3.9k 33k 220 1k 0.22 10k 68k 270k 2.2k 3.3k 47k 2.7k 3.3k 2.2k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 3W 1/16W 1/16W 2W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Film Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AA
å å å
å
å
44
Description 3.3k 560k 3.3k 560k 560k 3.3k 560k 3.3k 100 75 75 75 75 100 75 100 1k 1.2 2.2k 330 1 33k 6.8k 12k 100 100 10k 1.2k 100 68k 39k 27k 47k 100k 0.27 1k 0.27 27 0 150k 1k 1k 12k 10k 4.7 6.8k 390 1.2k 3.3 330 330 5.6k 47 9.1k 1k 10k 1.5 10 0.33 0.27 27 1k 10k 390k 1.2k 15 22k 1.5 820 0.47 18k 3.3k 3.3k 4.7k 22k 120k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1W 2W 1/16W 1W 1/2W 1/2W 1/2W 1/16W 1/16W 1/8W 1/8W 1/8W 1/8W 1/16W 1/8W 1/8W 1/8W 1/2W 3W 1/2W 1W 1/2W 1/16W 1/8W 1/8W 1/8W 1/16W 1/16W 1/2W 2W 3W 3W 7W 1/8W 1/8W 1/2W 1/2W 5W 1/16W 1/16W 7W 1/2W 2W 2W 1/2W 1/8W 1/2W 1/8W 1/2W 1/8W 1/8W 10W 1/2W 1/2W 1/8W 1/16W 1/16W 1/8W 1/8W 1/2W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Film Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Metal Oxide Carbon Carbon Carbon Carbon Metal Film Carbon Metal Film Carbon Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Film Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Cement Carbon Metal Film Metal Film Carbon Carbon Metal Oxide Carbon Carbon Carbon Carbon Cement Carbon Metal Film Carbon Metal Oxide Metal Oxide Carbon Carbon Carbon
Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AB AA AA AA AA AA AA AA AB AA AB AB AB AA AA AA AA AB AA AA AB AA AB AB AA AA AB AA AA AA AA AC AA AB AA AA AA AA AA AA
21FL91
Ref. No. R754 R755 R756 R759 R766 R767 R768 R802 R803 R804 R805 R806 R807 R808 R810 R812 R814 R815 R816 R817 R818 R823 R824 R826 R827 R828 R829 R830 R831 R832 R833 R835 R836 R838 R839 R840 R841 R842 R843 R844 R845 R1002 R1003 R1006 R1007 R1008 R1009 R1021 R1022 R1023 R1024 R1026 R1027 R1031 R1032 R1034 R1035 R1036 R1037 R1038 R1039 R1040 R1041 R1042 R1043 R1045 R1046 R1047 R1048 R1049 R1051 R1052 R1053 R1054 R1059 R1061 R1062
Part No.
★
VRN-RL3DB8R2J+ VRS-RG3DB150J+ VRS-RG3DB121J+ VRS-RG3DB101J+ VRS-CY1JF333J~ VRD-RA2BE103J~ VRS-CY1JF332J~ VRS-CY1JF682J~ VRS-CY1JF103J~ VRS-CY1JF222J~ VRS-CY1JF222J~ VRS-CY1JF222J~ VRS-CY1JF222J~ VRD-RA2BE273J~ VRS-CY1JF101J~ VRS-CY1JF101J~ VRS-CY1JF473J~ VRS-CY1JF473J~ VRS-CY1JF223J~ VRS-CY1JF473J~ VRS-RG3AB151J+ VRD-RA2BE101J~ VRD-RA2BE101J~ VRD-RA2BE101J~ VRS-CY1JF102J~ VRS-CY1JF471J~ VRS-CY1JF472J~ VRS-CY1JF393J~ VRS-CY1JF271J~ VRS-CY1JF822J~ VRS-CY1JF101J~ VRS-CY1JF332J~ VRD-RA2BE470J~ VRS-CY1JF105J~ VRS-CY1JF101J~ VRS-CY1JF124J~ VRD-RA2BE821J~ VRS-CY1JF471J~ VRS-CY1JF103J~ VRS-CY1JF185J~ VRS-CY1JF185J~ VRS-CY1JF183J~ VRS-CY1JF822J~ VRS-CY1JF822J~ VRS-CY1JF103J~ VRS-CY1JF183J~ VRS-CY1JF103J~ VRS-CY1JF101J~ VRS-CY1JF101J~ VRD-RA2BE271J~ VRS-CY1JF101J~ VRS-CY1JF000J~ VRS-CY1JF104J~ VRS-CY1JF101J~ VRS-CY1JF103J~ VRS-CY1JF103J~ VRD-RA2BE101J~ VRS-CY1JF103J~ VRS-CY1JF103J~ VRS-CY1JF562J~ VRS-CY1JF102J~ VRD-RA2BE273J~ VRD-RA2BE103J~ VRD-RA2BE101J~ VRS-CY1JF104J~ VRD-RA2BE101J~ VRS-CY1JF101J~ VRS-CY1JF183J~ VRS-CY1JF101J~ VRS-CY1JF183J~ VRS-CY1JF101J~ VRS-CY1JF104J~ VRS-CY1JF101J~ VRS-CY1JF101J~ VRS-CY1JF103J~ VRS-CY1JF102J~ VRS-CY1JF105J~
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Description 8.2 15 120 100 33k 10k 3.3k 6.8k 10k 2.2k 2.2k 2.2k 2.2k 27k 100 100 47k 47k 22k 47k 150 100 100 100 1k 470 4.7k 39k 270 8.2k 100 3.3k 47 1M 100 120k 820 470 10k 1.8M 1.8M 18k 8.2k 8.2k 10k 18k 10k 100 100 270 100 0 100k 100 10k 10k 100 10k 10k 5.6k 1k 27k 10k 100 100k 100 100 18k 100 18k 100 100k 100 100 10k 1k 1M
2W 2W 2W 2W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1W 1/8W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/8W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Metal Film Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
Code AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
Part No.
★
R1063 R1064 R1065 R1066 R1067 R1068 R1069 R1070 R1071 R1072 R1073 R1074 R1075 R1076 R1081 R1849 R1850 R1851 R1852 R1853 R1854 R1855 R1861 R1862
VRS-CY1JF103J~ VRS-CY1JF103J~ VRS-CY1JF103J~ VRS-CY1JF561J~ VRS-CY1JF152J~ VRS-CY1JF331J~ VRS-CY1JF152J~ VRS-CY1JF331J~ VRS-CY1JF152J~ VRS-CY1JF221J~ VRS-CY1JF101J~ VRS-CY1JF103J~ VRS-CY1JF331J~ VRS-CY1JF102J~ VRS-CY1JF103J~ VRS-CY1JF222J~ VRS-CY1JF472J~ VRS-CY1JF221J~ VRS-CY1JF221J~ VRS-CY1JF221J~ VRS-CY1JF103J~ VRD-RA2BE102J~ VRS-CY1JF121J~ VRS-CY1JF121J~
X X X X X X X X X X X X X X X X X X X X X X X X
FB701
RBLN-0020CEZZ+ X Balun, BLN-0020CE
S1001 S1002 S1003 S1004 S1005 S1006
QSW-K0202PEZZ+ QSW-K0202PEZZ+ QSW-K0202PEZZ+ QSW-K0202PEZZ+ QSW-K0202PEZZ+ QSW-K0114CEZZ
Ref. No.
Description 10k 10k 10k 560 1.5k 330 1.5k 330 1.5k 220 100 10k 330 1k 10k 2.2k 4.7k 220 220 220 10k 1k 120 120
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide
Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
BALUN AB
SWITCHES X X X X X X
Switch, CH-Up Switch, CH-Down Switch, VOL-Up Switch, VOL-Down Switch, MENU Switch, POWER
AB AB AB AB AB AC
MISCELLANEOUS PARTS å F701 å FH701 å FH702 J401 J402 J403 J404 J405 J406 P302 P407 P601 P602 P603 P701 P702 P705 P1001 P1002 P1007 P1008 P1011 P1012 RDA602 RDA501 RDA701 RDA301 RMC1001 å RY701
45
QFS-C3229CEZZ QFSHD1013CEZZ+ QFSHD1014CEZZ+ QJAKGA015WJZZ QJAKE0108CEZZ QJAKE0183CEZZ QJAKE0184CEZZ QJAKG0093CEZZ QJAKFA008WJZZ QPLGN0461CEZZA QPLGN0361CEZZA QPLGN0660CEZZ QPLGN0461CEZZA QPLGN0361CEZZA QPLGN0260CEZZ QPLGN0269GEZZ QTiPM0083CEZZ QPLGN0561CEZZA QPLGN0561CEZZA QPLGN0461CEZZA QPLGN0461CEZZA QPLGN0361CEZZA QPLGN0361CEZZA PRDAR0224PEFW PRDARA010WJFW PRDARA026WJFW PRDARA043WJFW RRMCU0222CEZZ RRLYJ0093CEZZ QCNW-A299WJZZ QCNW-A482WJZZ QCNW-A529WJZZ QCNW-A530WJN1 QCNW-A531WJN1 QCNW-A532WJN1 QCNW-A534WJN1 QCNW-A625WJZZ
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Fuse, T3. 15A 250V Fuse Holder Fuse Holder Jack, Jack, Jack, Jack, Jack, Jack, Plug, 4Pin (S) Plug, 3Pin (WO) Plug, 6Pin (K) Plug, 4Pin Plug, 3Pin (TP651~3) Plug, 2Pin (M) Plug, 2Pin Tip (SG) Plug, 5Pin Plug, 5Pin (BC) Plug, 4Pin Plug, 4Pin Plug, 3Pin Plug, 3Pin Heat Sink, Q602 Heat Sink, IC501 Heat Sink, Q701 Heat Sink, IC301 Remote Receiver Relay Connecting Cord (K) Connecting Cord (DF) Connecting Cord (YUV) Connecting Cord (AN) Connecting Cord (FAV) Connecting Cord (RAV) Connecting Cord (MTS) Connecting Cord (P706)
AB AA AA AE AB AB AB AE AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AD AB AD AE AB AD AC AC AC AC AC AB
21FL91
Ref. No.
★
Part No.
Description
DUNTKA599WEA0 PWB-B CRT UNIT TRANSISTORS Q853 Q854 Q855 Q894
VS2SC3789//2E VS2SC3789//2E VS2SC3789//2E VS2SA1015Y/1E+
X X X X
2SC3789 2SC3789 2SC3789 2SA1015Y
D859 D898
VHD1SS119//-1~ VHD1SS119//-1~
AB AB AB AB
L851
VP-MK820K0000+ X Peaking, 82µH 10%
C851 C852 C853 C880 C893
VCKYPA1HB221K+ X VCKYPA1HB221K+ X VCKYPA1HB221K+ X RC-KZ0153CEZZ X VCEA0A1CW336M+ X
DIODES X 1SS119 X 1SS119
AA AA
COIL AB
CAPACITORS 220p 220p 220p 0.001 33
50V Ceramic 50V Ceramic 50V Ceramic 3.15KVCeramic 16V Electrolytic
AA AA AA AB AA
RESISTORS R849 R850 R851 R852 R854 R855 å R859 å R861 å R863 R864 R876 R877 R878 R880 R881 R882 R889 R891 R892 R894 R895
VRD-RA2BE271J~ VRD-RA2BE470J~ VRD-RA2BE470J~ VRD-RA2BE470J~ VRD-RA2BE331J~ VRD-RA2BE331J~ VRS-VV3DB123J VRS-VV3DB123J VRS-VV3DB123J VRD-RA2BE470J~ VRD-RA2BE121J~ VRD-RA2BE121J~ VRD-RA2BE121J~ VRD-RM2HD332J~ VRD-RM2HD332J~ VRD-RM2HD332J~ VRD-RA2BE821J~ VRD-RA2BE561J~ VRD-RA2BE391J~ VRD-RA2BE152J~ VRD-RA2BE561J~
X X X X X X X X X X X X X X X X X X X X X
270 47 47 47 330 330 12k 12k 12k 47 120 120 120 3.3k 3.3k 3.3k 820 560 390 1.5k 560
1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 2W 2W 2W 1/8W 1/8W 1/8W 1/8W 1/2W 1/2W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W
Carbon Carbon Carbon Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
QPLGN0461CEZZ X Plug, 4Pin QPLGN0561CEZZ X Plug, 5Pin QSOCV0933CEZZ X Socket,
AA AB AC
DUNTKB271WEA1 PWB-E MTS MODULE UNIT INTEGRATED CIRCUITS IC3001 VHiCXA2074Q-1S X CXA2074Q IC3002 VHiMM1501XN-1~ X MM1501XN
AP AC
TRANSISTORS Q3001 Q3002 Q3004 Q3005 Q3006 Q3007
VS2SD601AR/-1~ VS2SD601AR/-1~ VS2SD601AR/-1~ VS2SD601AR/-1~ VS2SD601AR/-1~ VS2SD601AR/-1~
X X X X X X
C3001 C3002 C3003 C3004 C3005
VCE9GA1HW475M+ X VCKYCY1HB562K~ X VCQYTA1HM123K+ X VCEA0A1HW105M+ X VCEA0A1HW475M+ X
2SD601AR 2SD601AR 2SD601AR 2SD601AR 2SD601AR 2SD601AR
AA AA AA AA AA AA
CAPACITORS 4.7 5600p 0.012 1 4.7
50V 50V 50V 50V 50V
Electrolytic Ceramic Mylar Electrolytic Electrolytic
★
C3006 C3007 C3008 C3009 C3010 C3011 C3012 C3013 C3014 C3015 C3016 C3017 C3018 C3019 C3020 C3021 C3022 C3023 C3024 C3025 C3026 C3030 C3031 C3034 C3037 C3038 C3039 C3042 C3043 C3044 C3045 C3046 C3047 C3048 C3080 C3081 C3082 C3083
VCEA0A1CW106M+ VCEA0A1HW475M+ VCKYCY1HF103Z~ VCEA0A1CW227M+ VCE9GA1HW475M+ VCEA0A1HW475M+ VCE9GA1HW475M+ VCKYCY1HB272K~ VCQYTA1HM473K+ VCEACA1HC335K+ VCE9GA1HW475M+ VCEACA1CC106K+ VCEA0A1HW105M+ VCEA0A1CW106M+ VCEA0A1CW106M+ VCEA0A1CW106M+ VCEA0A1CW106M+ VCKYCY1HF103Z~ VCKYCY1HF103Z~ VCKYCY1HF473Z~ VCKYCY1HF473Z~ VCQYTA1HM682K+ VCKYCY1HF682Z~ VCEA0A1HW224M+ VCEA0A1HW335M+ VCEA0A1HW335M+ VCEA0A1HW224M+ VCKYCY1HB681K~ VCKYCY1HB681K~ VCEA0A1EW476M+ VCEA0A1HW335M+ VCEA0A1HW335M+ VCEA0A1HW335M+ VCEA0A1HW335M+ VCEA0A1CW106M+ VCEA0A1CW106M+ VCKYCY1HF103Z~ VCEAKA1CW106M+
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
R3001 R3002 R3003 R3004 R3005 R3007 R3008 R3010 R3011 R3012 R3013 R3014 R3016 R3018 R3019 R3021 R3024 R3025 R3026 R3027 R3028 R3029 R3030 R3031 R3032 R3033 R3034 R3035 R3036 R3080 R3081 R3082 R3083 R3084 R3085
VRS-CY1JF221J~ VRS-CY1JF221J~ VRS-CY1JF105J~ VRS-CY1JF104J~ VRS-CY1JF623J~ VRS-CY1JF332J~ VRS-CY1JF302J~ VRS-CY1JF392J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF102J~ VRS-CY1JF000J~ VRS-CY1JF272J~ VRS-CY1JF331J~ VRS-CY1JF392J~ VRS-CY1JF683J~ VRS-CY1JF392J~ VRS-CY1JF683J~ VRS-CY1JF182J~ VRS-CY1JF223J~ VRS-CY1JF102J~ VRS-CY1JF182J~ VRS-CY1JF223J~ VRS-CY1JF102J~ VRS-CY1JF101J~ VRS-CY1JF101J~ VRS-CY1JF103J~ VRS-CY1JF103J~ VRS-CY1JF103J~ VRS-CY1JF103J~
Description 10 4.7 0.01 220 4.7 4.7 4.7 2700p 0.047 3.3 4.7 10 1 10 10 10 10 0.01 0.01 0.047 0.047 6800p 6800p 0.22 3.3 3.3 0.22 680p 680p 47 3.3 3.3 3.3 3.3 10 10 0.01 10
16V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 16V 50V 16V 16V 16V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 50V 50V 50V 16V 16V 50V 16V
Code
Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Mylar Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Mylar Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic
AA AA AA AB AB AA AB AA AA AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
RESISTORS
MISCELLANEOUS PARTS P860 P880 SC851
Part No.
Ref. No.
Code
AB AA AA AA AA
46
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
220 220 1M 100k 62k 3.3k 3k 3.9k 1k 1k 1k 1k 1k 1k 1k 1k 0 2.7k 330 3.9k 68k 3.9k 68k 1.8k 22k 1k 1.8k 22k 1k 100 100 10k 10k 10k 10k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
21FL91
Ref. No.
Part No.
★
Description
Code
Ref. No.
Part No.
★
Description
MISCELLANEOUS PARTS P3001 P3002 P3003 P3004 P3008 P3009 P3012 P3013
QPLGZ0810CEZZ QPLGN0441CEZZ QPLGN0441CEZZ QPLGN0361CEZZ QPLGZ0810CEZZ QPLGZ0610CEZZ QPLGN0241CEZZ QPLGN0241CEZZ
X X X X X X X X
Plug, 8Pin (M) Plug, 4Pin (RAV) Plug, 4Pin (FAV) Plug, 3Pin (WF) Plug, 8Pin (N) Plug, 6Pin (SW) Plug, 2Pin (AV) Plug, 2Pin (AN)
AB AA AA AA AB AB AA AA
CABINET PARTS LOCATION
MISCELLANEOUS PARTS å ACC701 QACCZ3008PEZZ SP301 VSP1205PB09WA LHLDK0014PEZZ LHLDW1047PEZZ LHLDZ0063PEZZ LHLDZA096WJZZ LHLDZA107WJZZ TCAUS3000GJZZ XTASD30P12000 XTASD40P16000 XTASD40P20000 QCNW-A871WJZZ QCNW-A872WJZZ QCNW-A873WJZZ QPLGA0017CEZZ
X X X X X X X X X X X X X X X
AC Cord Speaker AC Cord Holder Wire Holder Anode Clamp Holder Holder Holder Caution Label Screw, x3 Screw, x8 Screw, x4 Connecting Cord Connecting Cord Connecting Cord Plug
AE AK AB AB AB AB AB AA AA AA AA AB AC AC AC
SUPPLIED ACCESSORIES ACCESSORIES RRMCGA108WJSA X Infrared R-C TiNS-A372WJZZ X Operation Manual
AT AE
PACKING PARTS (NOT REPLACEMENT ITEM) SPAKCA318WJZZ SPAKPA055WJZZ SPAKXA145WJZZ SSAKA0101GJZZ TLABM0005GJZZ TLABZA153WJZZ
-
Packing Case Wrapping Paper Buffer Material Polyethylene Bag Model Label POP Label
AS AE AK AB AB AK
CABINET PARTS 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9
CCABAA146WEH0 Not Avairable HBDGB3155CESA HDECQ119WJSA JBTN-A070WJSA MSPRC0005PEFW GDORFA015WJSA MSPRPA012WJFW HiNDPA194WJSA GBFL-A007WJZZ
X Front Cabinet Ass'y - Front Cabinet X SHARP Badge R/C Cover X Button, Power X Spring, for Power Button X Door Door Spring X Indication Plate X Baffle, x2
2
GCABBA088WJKA X Rear Cabinet
BC — AC AC AC AA AE AB AB AC AX
47
Code
21FL91
Ref. No.
Part No.
★
Description
PACKING OF THE SET
Ref. No.
Code
48
Part No.
★
Description
Code
21FL91
Ref. No.
Part No.
★
Description
Code
Ref. No.
-MEMO-
49
Part No.
★
Description
Code
21FL91
Ref. No.
Part No.
★
Description
Ref. No.
Code
Part No.
★
Description
Code
COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
TQ1456-S Dec. 2002 Printed in Japan In Japan gedruckt Design and Production Information Design : SEM Production : SEMEX
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
MY. DS
50
